plus fan 3d models

Remix of the "Anet A8 Plus Fan Duct" from Celil Türkmen Modified the attachment (expanded by .1mm on each side) to attach better to the extruder mount Original file here : https://www.thingiverse.com/thing:3749653

I redesigned the stock Plus fan shroud to encompass the hot end and provide airflow to the extruder from every direction rather than just the back side. This part attaches with the existing harware and replaces the stock fan shroud on the Printrbot...

for plus

part cooler for sapphire plus inspired by TWO TREES SAPPHIRE PRO part cooling duct by EG_13 January 29, 2020

Raise 3D N2 Plus fan cover http://www.tech-model.cz/catalog.php?cat=10

Remixed an ender 5 plus fan duct to fit on my fan. ...The previous one had some extra plastic on that the screws go through and didn't fit on mine.

Simple but effective replacement for your Ender 5 Plus duct fan. Exhaust in under small angle (now with rails) so air flow is pointed directly to the tip of the nozzle. Hope you will be happy with the results. In case of any problems or tips do not...

Simple but effective replacement for your Ender 5 Plus duct fan. Exhaust in under small angle (now with rails) so air flow is pointed directly to the tip of the nozzle. *Hope you will be happy with the results. In case of any problems or tips do...

Fan / duct mounting-bar and duct for the Wanhao D6 plus. Mount it on the right original fan-attachement M3 screws. you need 2x 4010 radial fans and 8x 2x8 screws. Print the duct 2x. ... Print it in ASA.

This is a fan shroud I made for the maker select plus style printers. Pops in the existing holes in the fan for the bolts. Need nothing extra to install. ...

For "Anet a8 PLUS" Due to heating problems, I designed this fan mount. No screws are required to secure the entire component to the extruder. ...The fan is mounted using M3 screws and nuts.

Direct Drive Fan Duct.

This is my version of the many replacement fan ducts for the Anet A8 Plus. I tried a number of the others and found that they either didn't fit the fan properly (falling out too easily) or pointed in the wrong direction. This latter point is to be...

These are the printable files for the two shrouds for the Printrbot Metal Plus

This is my version of the many replacement fan ducts for the Anet A8 Plus. I tried a number of the others and found that they either didn't fit the fan properly (falling out too easily) or pointed in the wrong direction. This latter point is to be...

Plus moving the openings away from the block allows the air to travel below the heater block to cool the part as oppose to the air hitting the block and bouncing most of the air away. At the same time I placed a couple of boss for the screws so...

... fits with fans of either 10mm or 20mm depth, uses the stock hardware to bolt in place. Print standing up without supports in one piece. Big credit to : https://www.thingiverse.com/thing:869692 for the inspiration to place the fan at the back

Hey Folks, I wasn't finding a design for one of these that fit my Anycubic Kobra Plus so I took some inspiration from other parts and whipped this up. It's my first CAD design (TinkerCAD), so definitely some room for improvement! I designed it to...

Remix of Red Squirrel Changes -Shroud/heatsink alignment -Fixed ABL mount -ABL cutout for wiring -Re-sized part cooling fan cutout Print with backside on bed, Support touching bed only Probe offset = #define NOZZLE_TO_PROBE_OFFSET { 32.1, -4.9, -3.3...

I intended them to self tap with m3 screws, but I ended up using longer screws and nuts to mount the fan to the thing. I also shimmed the 2 holes that hold the thing agains the panel with scrap extrustion string to... But I haven't gotten around...

<p>this is a remix of the passive cooler and the slim stepper cooler</p>

ANET A8 PLUS Extruder Fan part modification. I modified the extruder part. ... In the past, the inconvenience of using the bolt was converted into an open format.

A plate to mount two 4010 fans above an Orange PI 5 Plus. ...Standoffs are needed

... well on other 40mm fans. For the wanhao I3 plus you will need to print both files, one of them is for the 'extruder fan' and one for the 'cooling fan'. ...Two files are needed since the stock configuration of the screws is different on these fans.

Simple fan duct for Anet A8 Plus. ...The reason why I created is also simple, the original one wasn't stay tight in it's place.

A fan adapter for the Creality Halot-One Plus. the original fan is very loud, so a quieter one was needed, the original mounting points seem to transmit vibrations from the fan, hence the adapter printed in TPU. It is fastened with 6mm M3 screws,...

I did fan development work for the two tree bluer plus model. You just have to give up the stock holding iron. ...You will need 6x M3x20 and 3x M3x8 bolts to assemble the design.

I had a subscriber reach out to me asking witch Fan Duct would fit the ROBO 3D R1+Plus and I told him that the Novice Expert's Fan Duct should fit and he told me that it did not is I looked into it and well it was to tall for the R1+Plus with a stock...

Thanks to teivaz https://www.thingiverse.com/teivaz für your impression for a simple better fan duct. On my TwoTrees Sapphire Plus I get the problem, that the design was to high, so I remixed it with 1,5mm less high. ... Now I have 1mm space left...

Fan shroud and shim for the E3D V6 hotend.