po 33 case mpc 3d models

Simple case for a Teenage Engineering Pocket Operator PO-33 K.O! I don't have any of the other PO models to test with, but imagine it would fit them also. Simple design, slides in/out without forcing (but stays in). ...I printed this several times...

Simple case for a Teenage Engineering Pocket Operator PO-33 K.O! I don't have any of the other PO models to test with, but imagine it would fit them also. Simple design, slides in/out without forcing (but stays in). ...I printed this several times on my...

This is a casing for the PO-33 K.O. drummachine. I'm not sure if it would fit for the other versions, unless there are no differences. In order to use this you have to clip off the upper loop. The pictures show a older version of the design inwich...

3D printed Pocket Operator Case

This is ment to be used with the PO case from crashdebug. When not recording just clip it anywhere on the PO Case. Comes with the text REC embossed or engraved. Best printed with a signal color so you dont have it on the record button without...

So the low-tech solution is a little clip that keeps the record button pressed down, so you only have to selevt the slot to record to and done.This is ment to be used with the PO case from...

download TE OP case for test

This is a cover accessory the Teenage Engineering PO-33 Knockout that uses thumb screws to gently press down the record button and sound slot button for hands-free recording, enabling you to play your instrument. UsageSlide the pocket operator...

This is a kit which includes a zmr case cover to make a flat area for the battery to sit on (to prevent the screws biting into the battery), a top cover to prevent anything from damaging the battery and a low power alarm case (different page, can be...

Simple case for Li-Po 2S batteries with dimensions up to 99.5 x 34 x 20 mm (inner case dimensions).

po

po op

... ...Specifically designed to work with the nice minimalistic case by "The Case" : https://www.thingiverse.com/thing:5317194 I used a personal logo for my version which I photographed. The uploaded model has the teenage engineering logo instead. ...

This is case for a li-po battery 2S and 3S 145x50x25 - 2s 145x50x37 - 3s

I had a bigger Li-Po battery lying around than the original FlySight uses and realized the box would only have to be slightly bigger to fit it, so I made a new version that fit the bigger battery. A quick test shows that my FlySight runs 3.5 hours...

This is a 3D printed case for the Teenage Engineering Pocket Operator 12 Rhythm Machine based off of the silicone case available for purchase on their site. UPDATE: This case has been remodeled around the official CAD models released by Teenage...

Case & Stand for my PO12, PO14 & PO16. You can use it with or without the stand. ... Sounds a bit "raw", because the speakers are closed now You need: 2pcs M3 x 20 (DIN912) and 2pcs Nut M3 (DIN934)

This is a 3D printed case for the Teenage Engineering Pocket Operator 12 Rhythm Machine based off of the silicone case available for purchase on their site. UPDATE: This case has been remodeled around the official CAD models released by Teenage...

added a Rick and Morty tag on the top of the front case and made some buttons but I do recommend printing the buttons in higher resolution mine came out a little iffy

Pocket operator case back with a female mount compatible with the modular mounting system (https://www.thingiverse.com/thing:2194278). Unfortunately you need supports but they will be inside so the outside will be clean. ...I printed using a Prusa...

mini mpc akai

Customized version of http://www.thingiverse.com/thing:58091 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58091

The specific components are: - Arduino Nano 33 IoT - 0.91 inch OLED display - TP4056 Charging module - MAX4466 Electret Microphone - SPST Switch - 18650 Lithium Ion Battery I designed this case for an audio/vibration tachometer I'm building and...

Simple battery brace for the Pocket Operator family. Designed to prevent sudden powerloss due to loose batteries. Simple and easy print. ... Tested on a PO33 and printed with a Ender 3 V2

Compact Case for Arduino Nano 33 BLE Head Tracker, in two variants: - For the Basic version ABX00030 - For the Sense Version ABX00031, with an opening for the proximity sensor Additional parts needed: - 3pcs LED port covers, 4x4x2mm transparent...

Drum Machine Akai MPC legendary miniature non-functional, for pendant making or decorative purposes.

http://www.thingiverse.com/apps/customizer/run?thing_id=51376 Instructions Using the following options: _5c_labelDepth = -0.3 _1a_batteryDiameter = 10.7 _3a_walls = 0.5 _4a_magnetType = cylinder _3b_base = 0.8 _5a_labelText = AAA _4c_magnetHeight =...

Customized version of https://www.thingiverse.com/thing:194066 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=194066

I designed this case for a powerbank with w332 board and a 1260100 li-po 10000mA/h battery. ...To secure the lid onto the case, glue is requiered.