pocket operator tonic case 3d models

This is a simple case for the "Pocket Operators". You can store a short cable inside it and the operating manual. Have fun ! ...:) www.3Dsection.de

A remake of "Pocket Operator Case (OP-1 Style Keypad)" by justinkowski. I changed the style of the buttons and add some minor improvement to better allocate the operator into the case especially when with the hanger still on. ...

A case for the Teenage Engineering Pocket Operator series https://teenage.engineering/products/po Compatible with or without detachable hanger. Depending on printer precision, it may be necessary to rearrange buttons for best fit. ... Feedback is...

This is case for the pocket operator that contains microphone. Following are the features for my model. LED lights are visible. Don’t need to harm the hanger. Wire stand is still available to use. Designed to use snap fit for assemble. I...

(It fits my PO-33 and PO-20) Almost all features of the pocket operators work with the case. The top hanger can be left on or taken off, the input and output jacks are accessible, the wire stand is fully functional, there is a space for the...

this pocket operator case is a retro model it is elegant design that only 3 parts 1. 1 upper case 2. 23 buttons 3. ... 1 bottom case easy to print is easy to assemble and I want to make it cheap so everyone else can buy it too and have fun :)

Protect your Pocket Operator and make it easier to hold with this sleek two-piece case. It accommodates most plugs for the line-level audio jacks. If not, you can simply remove the top part of the case to facilitate cable ingress. The case does not...

This is a slip on back case for pocket operators that have the silicon case. There are two versions one for the 10 series and one for the 20 series. ...The 1/8 TRS jacks are slightly offset between the 10 and 20 series.

A carry case for Teenage Engineering's Pocket Operators. Based off of the internal dimensions of ipsofatso's Pocket Operator Sleeve. My version is a little wider, has a 2.5mm wall width all the way around, is closed on the bottom, and has a lid. I...

This is case for the pocket operator that contains microphone. Following are the features for my model. - LED lights are visible. - Don’t need to harm the hanger. - Wire stand is still available to use. - Designed to use snap fit for...

If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad This is a fully enclosed case and button set for the Teenage Engineering Pocket Operator series. It protects...

If not, you can simply remove the top part of the case to facilitate cable ingress. The case does not require any hardware to assemble, though after printing you will need to spend some time carefully removing supports from the PCB grooves around the...

Case for Teenage Engineering's Pocket Operator. This case is compatible with the wire folding stand, and the loop at the top doesn't need to be removed. All LEDs shine through a small hole above each button, and there is a hole to allow the use of...

... be able to move without any resistance. Assembly See instructions on the included pictures. Videos Showing some of the prototypes and the case printed at shapeways. Short demo of 2 pocket operators using this case.

This is a case for the Pocket Operator series of synthesizers made by Teenage Engineering. Its main features are: Keys move freely LEDs are still visible Audio sockets accessible with standard sized rubberized jacks Possible to keep the break-away...

... imperfections. The buttons must be able to move without any resistance. Assembly See instructions on the included pictures. Videos Showing some of the prototypes and the case printed at shapeways. Short demo of 2 pocket operators using this case.

Leave the connectors of the buttons on when putting in the case. I noticed when you take of the frontcase from the plate, if it is still warm it could bend near the screen frame, this makes it look like it is hitting something from the inside and...

***Updated back plate 25/09/21*** Designed a simple two part PO case, while trying to retain as much of the original style as possible. Features: Keep the metal stand Keep the snap off hanger Access the original buttons for tactile response...

I remixed the Pocket Operator case to add buttons to it and reinforce the case with places for 4 screws to hold it together. ...It takes 4 - 2.5M x 12mm screws (self tapping).

I remixed the Pocket Operator case to add buttons to it and reinforce the case with places for 4 screws to hold it together. ...It takes 4 - 2.5M x 12mm screws (self tapping).

I remixed the Pocket Operator case to add buttons to it and reinforce the case with places for 4 screws to hold it together. ...It takes 4 - 2.5M x 12mm screws (self tapping).</p> Category: Audio

Just like the pocket operators are of minimal design, this case is just big enough to hold and protect a pocket operator, and nothing else. You might even need to shave off the remnants of the hanging tab to get your PO to fit. I recommend small side...

Simple case for a Teenage Engineering Pocket Operator PO-33 K.O! I don't have any of the other PO models to test with, but imagine it would fit them also. Simple design, slides in/out without forcing (but stays in). ...I printed this several times...

Simple case for a Teenage Engineering Pocket Operator PO-33 K.O! I don't have any of the other PO models to test with, but imagine it would fit them also.</p> <p>Simple design, slides in/out without forcing (but stays in). ...I printed this several...

Designed a slide-over case for my PO-20. ... Cutouts for the knobs and batteries, but protects the buttons from constantly turning on in your pocket.

This is a travel case for the pocket operators by teenage engineering. Specifically designed to work with the nice minimalistic case by "The Case" : https://www.thingiverse.com/thing:5317194 I used a personal logo for my version which I photographed....

3D printed Pocket Operator Case

... that has a microphone cutout. The only pocket operator I own is the PO-33 KO. Even though i'm confident the cutouts for the case will work for the other pocket operators please let me know if it does not. Or, remix it yourself! Enjoy! ...:)

A stencil that can easily be printed for cutting stickers to fit on the pocket operator silicone case. This model was specifically designed for K.O! ...Previous models may have slight changes.

I wanted a custom lid for the PO-20 case, so I changed the 'arcade' text from the original build to a space invaders sprite. ...Love the build, definitely go check it out for your pocket operator.