polaroid camera blue 3d models

Minimal polaroid picture stand, for both portrait and landscape orientation. Length of the stand can be adjusted to fit one or more pictures. Customizable in OpenSCAD or using the Thingiverse Customizer. ... STL design dimensions: - Stand length...

This versatile two-piece case allows you to safely store up to 36 Polaroid instant photos in SX-70, 600, or I-Type formats. ...The top photo is cleverly showcased through the clear front panel, surrounded by a subtle border that adds a touch of...

Polaroid Cube Mount Carefully measured using digital calipers attached to the suction mount. All measurements are listed in metric units (millimeters). ... Updated features include adding inner recesses, removing the inner wall below the lip, and...

The polaroid go stand is printed at a layer height of 0.16-0.20mm minimal support needed, can print without. The design currently has some roughness I'm still learning CAD software, the overall quality is decent. ...Good present for friends and family!

I Made This Scan Adapter for Scanning Polaroid Pictures Without Newton Rings, Feel Free to Modify It to Suit Your Needs. To Use This Adapter, You'll Need a Little Double-Sided Tape or Simply Folded Over Tape to Secure the Photo Against the Back of...

I'm printing a frame to hold my Polaroid Zip ZINK photos that are only 2x3 inches. It's 3 millimeters thick and has a small, -1 millimeter gap inside the edge. The border is two millimeters wide. To give it some weight, I'm using a hundred percent...

I made this simple frame to fit a large size Polaroid instant photo (89x108mm). The slot in the back is cut out to allow for easier removal of the photo without touching the front. I printed it at 0.2mm layer height which took around 4.5h including...

Wanted something to protect my polaroid go film while it develops instead of putting the film in my pocket where it could get scratched and damaged so I designed this. It is still pretty basic and I will most likely make some changes to it. ... If you...

I made this simple frame to fit a large size Polaroid instant photo (89x108mm). The slot in the back is cut out to allow for easier removal of the photo without touching the front. I printed it at 0.2mm layer height which took around 4.5h including...

A mount for the flash is provided (remixed from Albert's excellent design) which you can screw a focused flash mount from an old camera onto. I took the louvers out of the flash to get full power all the time and calculate using a GN of 140 at ISO...

This is a frame for a polaroid zink paper photo (50x30mm). Each photo requires a frame, and either the portrait or landscape backing, depending on which way you want to show the photo. The back is supposed to be a tight fit, and you will have to bend...

Get ready to be amazed by stunning light effects like the 'Cityscape at Sunset' scene, all within a Polaroid-inspired frame that's as stylish as it is unique. ...The included file contains everything you need: the lamp frame, wall bracket, and...

Lens splitzer for double exposure on the Polaroid OneStep+. This covers half of the lens to keep half of the film undeveloped when shooting double exposures. To use, adjust the splitzer to cover half of the lens, take one exposure, turn the splitzer...

I purchased a Polaroid Filament Weight Scale and quickly discovered that the holder was too short for my Schmelz Bar filament. Therefore, I designed a new one specifically for 90mm wide filament rolls. This design can be edited as desired and was...

With this Polaroid Now accessory you can “mix two of your friends’ faces in one shot, combine different scenes in a picture, or pair unlikely objects in one photo. It cuts each photo into a half frame, only exposing one half at a time to mess with...

Polaroid film frame designed to hold 2 pictures, displaying one on each side. This frame was made to work with i-Type film (107x88mm) but may also fit other films of the same size. When inserting pictures into the slots at the top, they should slide...

Polaroid, Stl file for 3D printing Size Width or length: 8 cm/3.15' (maximum size), other side is in proportion Height cutting edge: 1,1 cm/0.43' Height details: 0,8 cm/0.31' 💡💡Easy to print designs💡💡💡 !! For personal use only! You may not...

The Polaroid Cube Mount for Quadcopters is a versatile solution that allows users to capture aerial photos and videos with ease. The mount consists of two main components: the smaller "seat" and the larger "shell". To assemble the mount, simply place...

This is a sturdy tripod holder designed specifically to support the Polaroid SX-70 camera.

Covered your plain toilet paper holder with a Polaroid camera for your own design toilet room.

This adapter makes it possible to apply a spectrum filter to your Polaroid SX-70 camera.

I made the inside dimension a little larger so the cube wasn't so hard to remove.Category: Camera

Free Polaroid 3D Model Available Now

This camera is totally awesome - it's like a boss! The pictures develop right before your eyes and they look insane! I'm talking jaw-dropping, mind-blowing good! ...It's like magic, but real!

I'm designing a straightforward PCB for LoRa and the Blue Pill, along with GPS integration. My own version featuring Dupont connectors hasn't proven stable, nor have boards utilizing fiducials for OPENPNP. ...The presence of massive 0.75mm tracks is a...

A breathtaking masterpiece showcasing the mystical Blue from "Wolf's Rain" is now unveiled. Crafted with precision in Blender, Marvelous Designer, and Zbrush, this artwork boasts intricate details that leap off the screen. The textures, woven with...

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: hole_radius = 3 Font = write/orbitron.dxf stick_thickness = 3 font_thickness = 5 stick_width = 8 flat_bottom = 1 message = BLUE font_size = 10

For this particular version, settings include stick width of 8, font size of 10, blue message color, hole radius of 3, the 'write/orbitron.dxf' font style, stick thickness of 3, and font thickness of 5. ...Additionally, the flat-bottom option has been...

https://www.thingiverse.com/apps/customizer/run?thing_id=46704 Instructions Using the Following Options: Font = write/Letters.dxf text1_rotate = 350 text2_thickness = 3 text2_size = 14 ring_outer = 10 image_scale = 1 my_text2 = BLUE my_text1 = ring_y...

However, I still wanted to take it a step further by developing a custom mount specifically tailored for my quadcopters, ensuring that my expensive GoPro camera would be adequately protected. In order to accomplish this, I simply edited out the...