pololu vl53l0x 3d models
1121 3d models found related to pololu vl53l0x.thingiverse
Support for array of 3 Pololu VL53L0X Time-of-Flight distance sensor carriers (https://www.pololu.com/product/2490) for robotic 2D environment mapping and SLAM. The lower support attaches to a servo horn. The three sensor carriers are fixed to the...
grabcad
Model of the ST VL53L0X proximity sensor.More information, datasheet etc.: https://www.st.com/content/st_com/en/products/imaging-and-photonics-solutions/proximity-sensors/vl53l0x.html
prusaprinters
The Vl53l0x is what's known as a time of flight sensor.This sensor can measure a distance using a laser!However these sensor are well.. ... sensitive and can detect a transparent visor pretty easily.<br>As it is usually not possible to place the...
thingiverse
This is vesion zumo pow for vl53l0x sensor. This is good replacment for sharp IR sensor. ... Regards
grabcad
Simple model of VL53L0X V2 Time of Flight sensor.Model and render done in Creo Parametric. ...STEP and Creo 5.0 model given.
thingiverse
STMicro's VL53L0X is good distance sensor, But this sensor need to be calibrated with certain condition because each device has own offset error. Document said 100mm distance calibration target is shown for this procedure. This calibration plate...
thingiverse
Was looking for a mock up for the VL53L0X distance sensor, but couldn't find one. So i made it. ...This is just to get the dimensions right when making something with these tiny sensors.
thingiverse
Case for a VL53L0X TOF Sensor + NodeMCU V3 (ESP8266, AZDelivery) Designed for mounting on top of the motor track of the garage door (as shown in the pictures). ... No screws needed, just clips into the mounting holes of the esp and the sensor.
thingiverse
Hi All, There is One More Orange Thing ;) Today i have created a Case for the VL53L0X TOF Sensor. The Case is screwable topdown, so i am able (you too ;)) to mount it at the ceiling and measure to the bottom. ... have fun with it
thingiverse
... HC SR501 PIR enclosre, this design uses the same wemos bottom but a VL50L0X specific cap. ...The VL53L0X should just snap in place without screws. This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/g1jV0WxR6Eb
thingiverse
This is a simple case made for the Adafruit Vl53L0X time of flight sensor. https://www.adafruit.com/product/3317 A useful little sensor for robotics or in my case a Machine vision system. It may fit the VL6180X but I have not tested that to...
grabcad
Aluminum L-Bracket for Gearmotors 17x17.7mmLİNK: https://www.direnc.net/reduktorlu-motorlar-icin-aluminyum-l-braketi-cifti-pololu
thingiverse
this is a pololu stepper board for the reprap, it has on it all the power and end stop inputs and outputs. this has the ability to set the micro stepping on it, with jumpers. i have updated it a little since i posted the pictures, there is now a...
thingiverse
I was looking for a couple of mounts for some Pololu boards and couldn't find any, so I made some. The board I am using are the Mini Maestro 18 and the 2882 15A regulator to drive the 12 servo's I am using for my Raspberry Pi controlled biped. I...
thingiverse
This is casing for VL53L0X time of flight ranging sensor
thingiverse
Case for Adafruit Vl53L0X time of flight sensor. ... Original Design: https://www.thingiverse.com/thing:2831925
thingiverse
... board. More info - https://medium.com/robotics-weekends/vl53l0x-vs-hc-sr04-range-sensor-part-1-99934cbcda81 If you found this useful, please donate what you think it is worth to my paypal.me. Help cover the time of design. Thanks, Enjoy! ...
thingiverse
The VL53L0x lidar distance sensor is inexpensive and quite accurate, unless the small sensor is directly in the sunlight. ...This extends the box to help keep the sunlight from affecting the laser sensor.