porsche boxster 986 cup holder 3d models
365645 3d models found related to porsche boxster 986 cup holder.thingiverse
Remix of trevorbattle's Cup Holder design. This has a base for the print so you can place things inside (besides drinks) and not remove it to grab something. Fits nicely in my car. Despite being PLA (in my case) it has yet to melt in the Florida...
thingiverse
Remixed to fit American size drinks. ...Can fit a small camelbak water bottle or 32oz soda cup. ... Print upside down with supports.
thingiverse
... can use that space for a double-din stereo upgrade. The lid can still close and lock with the cup holder in place. With the Boxster the lid opens all the way clear of the cup, I suspect with the 911/996 the door might sit on the cup a little bit.
thingiverse
A simple holder that fits perfectly in the Porsche Boxster S 986. Tried it in my 2001, so should fit all in the same range. You could lower the bars holdin the can in place, but i'd rather have them higher to prevent them from being shaken to...
thingiverse
Printed in ABS, requires a the type of phone holder with a magnet on the phone and a sphere glued to the holder. ...The printed holder needs to be attached with screws or tape so that when you take the phone off, the whole thing does not come out, there...
thingiverse
This is a Phone Mount for my Porsche Boxster 986 S Spyder from 2004. The ball joint allows you to change the viewing angle of the Tablet/Phone you want to use. I Custom made the mount to perfectly fit on the upper right part of the storage...
thingiverse
Removable cupholders for Porsche 986 Boxster. Bracket wedges in between Center dash and Upper Center Console as shown. Cupholders can be stored in armrest when not in use. Assembly Instructions: 1. Insert the shorter side of bottom supports...
prusaprinters
I went ahead and created new fonts and numbers for our Porsche 986 as the old one were long gone. This has been our fixer upper car and it was great to print a part that are as expensive as 80 euros. </p><p>The print is pretty simple and is as...
thingiverse
Push Connecter into iPad holder with connecter arm facing the shorter half of the iPad holder 4. line up holes on the Car Mount to connecter piece with the arm looking like \\ 5. Push connecter tube into Car mount 6. ...Turn clockwise until...
thingiverse
This is a cam holding tool for the Porsche 986/996 Boxster or 911 early 5-chain engines.
thingiverse
Add a cup holder to a Porsche 996 or 986 that has the ashtray delete part installed. Pull up the rubber liner and remove the two screws. Place the bottom piece in position - it only fits one way. Replace the screws. Insert the top piece. Done. ...As a...
thingiverse
This phone holder was designed to fit the phone holder below, which can be purchased from Amazon. ... Link: https://www.amazon.com/dp/B07KF7R8L2?psc=1&ref=ppx_yo2ov_dt_b_product_details General Print Settings Material: PETG-CF Layer Height: 0.2...
3docean
The 3D model was created on real car base. It’s created accurately, in real units of measurement, qualitatively and maximally close to the original. Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi...
grabcad
Measured from actual part.Mounting dimension tolerance +/- 0.25External dimension tolerance +/- 1.2500 Boxster S Porsche 986 L R REAR Red BRAKE CALIPERS # 996352421 996352422 86,562
thingiverse
This is a remix of a great original design by trevorbattle. I have modified it with a center support that helps it sit level and not shift in the compartment. The lid still closes over it. It's easy to pull out and re-install. 124g of...
thingiverse
Ball mount for phone holder for Porsche 986 stock stereo. I modified it from: https://www.thingiverse.com/thing:4706682 in TinkerCAD the ball appears to be about 17MM. Worked perfect with a phone holder I already had. ... I printed it and put...
thingiverse
... seal. ...It should work for Boxster 2.7 engine up to 2004 with a 'new style' PTFE oil seal that needs to be installed at 13 mm depth. Check your service manual to confirm it's what you need. ...Design is provided as-is without any kind of guarantee.
cgtrader
The 3D model was created on real car base. Itâs created accurately, in real units of measurement, qualitatively and maximally close to the original.Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi Format)...
cgstudio
The 3D model was created on real car base. It’s created accurately, in real units of measurement, qualitatively and maximally close to the original.Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi Format) -...
grabcad
fuel cap hinge missing? ...print itABS tested for 3 months, no crack
cgtrader
The 3D model was created on real car base. ...It’s created accurately, in real units of measurement, qualitatively and maximally close to the original.
thingiverse
These are paint plugs for the front calipers on the Porsche 986 S. You will need 2 of the large plugs, 2 of the small plugs, and up to 5 of the brake line plugs. I printed these in PLA. ... General Print settings (FDM) Layer Height: 0.2 mm Wall Line...
3docean
This is a car accessory to convert a Porsche Boxster 987 P2 cupholder into a Galaxy note 5 or 8 holder.
cults3d
Designed to fit the Tamiya 1/24 Porsche 986 Boxster. ... The insert resembles the trunk reinforcement of the real car.
cgtrader
The Boxster is Porsche's first vehicle designed from the beginning as a roadster; all previous Porsche convertibles were based on hardtop coupes.The first-generation Boxster (the 986) was introduced in late 1996 as a 1997 model; it was powered by a...
cgtrader
The Boxster is Porsche's first vehicle designed from the beginning as a roadster; all previous Porsche convertibles were based on hardtop coupes.The first-generation Boxster (the 986) was introduced in late 1996 as a 1997 model; it was powered by a...
cults3d
Designed to fit the Tamiya Porsche 986 Boxster. Theoretically, it should fit the Porsche 996 from Tamiya too, but this is still untested. The insert resembles the hood reinforcement of the real car. 2022-06-08: Altered the design to aprox 30%...