power amp rack 3d models

for our needsthis is our 19" Power AMP rackwith 2 x EP4000 Berhinger - Power amplifierhttps://www.thomann.de/fr/behringer_ep4000_europower.htm1 x CX2400 Berhinger - Active filterhttps://www.thomann.de/fr/behringer_cx3400_super_x_pro_v2.htm2 x PSD-2...

hinge for amp rack door

Power_mod_amp

Top rack is for suca tube amp and bottom is for fosi tpa3116 mini power amp. This is my v3 with increased cooling for the fiiO via chimney stacks that wrap around the fiO. I will be working on v4 with tighter tolerances for the inset on the...

A rack for the Sennheiser GSX 1000 and Magni 3 in a stackable format. There is adequate ventilation for both devices. ... You may need to remove the feet from the Magni for clearance.

It has a sliding lid to give access to screwing in power and loudspeaker connections through access holes. The OpenSCAD file has options for the audio input openings. Either a front access for the on board jack plug or rear panel for linking...

Power supply 1.3 Amp

Power Rack

Power rack

Power rack

power rack

Simple audio rack designed to hold two (or more) D-Class amps like the Aiyima A07Rack main pieces and side supports should be printed right side up, the top though should be printed upside down to limit the risk of the interlocking holes becoming...

http://www.thingiverse.com/apps/customizer/run?thing_id=60392 Instructions Remixed to fit over 20 amp power supply. The holes allow for a flat power cord and round output cord to be attached without additional hardware. I use two zip ties to keep...

This is a remix to fit over a 20 Amp power supply. The wires are run directly without the need for a power plug. Customized version of http://www.thingiverse.com/thing:60392 Created with Customizer!

... and cut it with a dremel tool so that I could make a mount for the power Inlet. This worked for several years but it eventually cracked and had to be replaced. This time around, I will install the mount plate I created and a new power inlet.

This Cover is for a 30 Amp Switch Mode 113 x 50mm

Power Rack made on catia for home workout

A simple power rack design! ...Free to use!

No description provided.

High end stereo power amp

Replacement power button for crown Macro-Tech Power amp

This is a rear bracket for mounting a QSC amp in a rack case. ...I didn't like the ~45lbs amp resting only on the 4 front screws in the rack, so I designed a quick bracket to help support the amp from the rear.

DPS8005 and power supply 80 volt 5 amp

High-End DAC HEGEL H190 and HEGEL Power AMP H20 combo with black wood custom stand.

A mounting case for a power supply, can be used with some 20 & 30 amp PSU's out there. Measure before you print, some power supplies are larger and some are smaller. ...You should be able to scale this to fit your needs.

This project will allow you to have a base to mount your 15 amp power inlet to. It is fully centered and has pre drilled screw holes. ... I would place butyl tape on the bottom of the mount and then screw on.

This is for a 24 volt 15 amp switching supply. ...The 12 volt 15 amp is a bit smaller I believe but not sure.

Vertical PSU base for larger 30amp power supply.

I made this power supply to mount a 60 watt power supply for a string of LED I put in the kitchen under the cabinets. You can find a new use for it! ...Enjoy!

This is a power supply we use and I decided to get a bit more intricate with the details. ... My first try at fine detail for the model and using illustrator to recreate the label for it.