power raspberry pi from ender 3 3d models

Just a simple mount for my Raspberry Pi Zero 2 W on my Ender 3 Pro! It fit under the screen by sliding the case on the v-slots extrusion. The case fits nicely and does not need hardware to be held in place. However, the case is 2 parts to allow...

This is a bracket for the brilliant Raspberry Pi 3b case (https://www.thingiverse.com/thing:3723561) I printed it at 100% and it fits the side rails of the Ender 3 v2 perfectly. It's a tight fit .. so you need to wiggle and make sure it's lined up -...

... bundle. ...Since the part is small, print with brim. Print with PLA, PETG. No support required. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: No Infill: 20% Filament: Overture PETG Category: 3D Printer Parts

Raspberry Pi Camera v2 case with a mounting arm for an Ender 3 V2 (also probably Ender 3) modeled as a mini security camera. -- Arm piece is not compatible with BLTouch. See remixed arm for a compatible version -- 5 separate parts in total,...

To install the pi angle the usb and ethernet ports in, just past the front, then push down on the long side opposite the power and HDMI, then push down the side that had the power and USB and it should snap into place 3. Attach your pi cam cable and...

Front mounted camera mast designed specifically for the Ender 3, expertly remixed from jcantalupo's original camera mast on Thingiverse. ... This innovative design is perfectly suited for use in conjunction with: - lrpena's pi case (available on...

... allow enough clearance for easy sliding in. This design is best suited for assembling a printer straight out of the box. This revised design allows for the raspberry pi case to be mounted directly onto the rails, streamlining the assembly process.

Slightly modded (smaller vent gaps) of the case by DotNetWorker Used Ender 3 bracket by FONSWERKS to make a slide-on mounting bracket for the rails of the Ender 3 V2 without blocking any ports. Bracket should fit snuggly around the Pi case, but still...

Using a 5V Noctua fan powered directly by the Raspberry Pi, I've managed to lower the Raspberry temperature by around 10º C. I used this converter (https://www.amazon.com/gp/product/B0768D2NYH/ref=oh_aui_search_asin_title?ie=UTF8&psc=1) for my...

This is a front mount for a Raspberry Pi camera on the Ender 3 Pro. I created this mount because all available designs were side mounts, which provide a poor viewing angle for the printer. With the camera positioned in the front, it captures much...

Remix of my [Ender 3 Raspberry Pi Case Clip](https://www.thingiverse.com/thing:3051848) for lower-profile cases such as [this one](https://www.thingiverse.com/thing:922740) by [0110-M-P](https://www.thingiverse.com/0110-m-p/designs). See the original...

This is a simple mounting bracket for my raspberry pi official 7" touch screen case.

The pi works via the original 24V power supply of the ender to which I added a voltage converter LM2596S set to 5.1V, I do not go through the USB port to power it but through the GPIO ports (as on the vorons). I printed 4 frame_extension to extend...

Raspberry Pi Camera v2 case with a mounting arm for an Ender 3 V2 (also probably Ender 3) modeled as a mini security camera. Mounts to the bed using the leveling bolts. No extra hardware needed for assembly. The camera housing snaps together and...

Housing for a BTT Octopus (Pro) on Ender 3 (Pro), with TFT35 V3.0, MOSFET and Raspberry Pi 4, 2ea 80x80x15mm Fan Only screws, nuts, washers and sliding blocks are required for assembly. Printed in PETG with 0.6mm nozzle. There is still room in...

Wide angle Raspberry Pi camera bed mount, case and camera arm remixed to fit my Ender 3 Pro. The original wide angle file works well, but I prefer the way a time lapse looks with a static bed. I have also included an extended bed mount if you...

From [Raspberry enclosure](https://www.thingiverse.com/thing:4586351) of [eoyilmaz](https://www.thingiverse.com/eoyilmaz). Remix to fit Raspberry Pi 4 with heatsink. The bottom heatsink sticks out just as much as the IO on the back of the board, the...

ENDER 3 V2 Raspberry Pi 4 Case Notes: this case is designed to hold a Raspberry Pi 4,2 30mm fans and 2 Buck Converters I'm intending to use the Arduino to prototype some different/unusual sensor integrations to the Printer print Settings: nozzle...

I added a fan for the Ender 3 V2 box by @pedrolamas My Pi 3B has heatsinks on it and since it runs 24/7 a fan is a must have. ... I run all fans as intakes

Remix : - Less material - Upper camera - Ribbon exit from bottom Works for Ender 3 and Pro

Remix : - Less material - Upper camera - Ribbon exit from bottom Works for Ender 3 and Pro

On my Ender 3, I used an excellent Pi case from https://www.thingiverse.com/thing:3075921 and mounted it upside-down underneath the LCD display. Then, I glued my cable guide to the side of the case. The ribbon cable is routed between the upper and...

Someone asked me to design a Raspberry Pi case that would mount on the display You will have to use supports to print this file. ...This was designed to fit the Raspberry Pi 3B and 3B+

A Raspberry Pi 4 upgrade that adds a sleek, modern design to your existing model B+ or A+, complete with an impressive top section adorned with the iconic Raspberry Pi logo and a sturdy bottom portion featuring the V2 design.

This is a Raspberry Pi Zero 2 W case for the Ender 3 Pro. After building a Voron and using Klipper and Mainsail/Fluidd, I had to convert my Ender over. Highly recommended I wanted something that mounted close the MCU so I could use UART between my...

Modified Syntax's original file to support the Raspberry Pi 4B. ... Link to original: https://www.thingiverse.com/thing:4597864

The camera ribbon cable also gets routed around to the back where it can be directed through my cable chain design to the Raspberry Pi Case mounted at the base of the printer. The camera case snaps together for the model Arducam that I have, but...

(This is primarily for the Pi 4b+) The DC jack can be used to power the pi, and also other components like led lights, if your power supply has the available power. There is a hole in the bottom of wires to run in an out for tidy connections into...

... is remix of the Pi Case by Metalluka. ...This is compact version compatibile with E3D, E3D Pro with 40 mm V-Slot construction. Better access to plug/unplug CSI camera connector for Pi Camera Cap added. Tested on Raspberry Pi 3B+, Raspberry Pi B 2014

Simple mount for a Raspberry Pi Camera off of the X-Axis where the belt tensioner is located. ...Has simple "tabs" to hold the cable in place.Included Step and Parasolid files for remixing as you see fit.[EDIT]Added a smaller mount that sticks out from...