power raspberry pi from ender 3 3d models

Installed adaptable interface connectors, and cord receptacles, borrowed directly from a reliable online resource at thingiverse.com, specifically the design with ID 3256773.

Remixed from this one (https://www.thingiverse.com/thing:3026059) with the "roof" thinner to allow the fitting of Rpi with heatsinks. Printed with the SD Card side on the bed without supports. ... Note : use the cap from the original thing...

A remix of a remix of the camera arm from https://www.thingiverse.com/thing:4721088. ... This arm has been extended to prevent it from being hit by the left Blower duct of the Hero Me Gen5 and gives clearance for a BLTouch. ...

This camera arm has 10mm opening for upgraded bed springs. ...You will need the rest of the parts from DustyNorm's [bed mount](https://www.thingiverse.com/thing:4634481). ... __Note__: this is the long arm version

This setup enables a Raspberry Pi 3 or 4 to be securely fastened under the LCD controller screen of an Ender 5 printer. Two M3 screw holes are provided, one requiring a 20mm M3 screw for added stability as it passes through both the PI's board and...

Raspberry pie model made in Autodesk Fusion 360

I also used another LCD display MPI3508 3.5 inch (I cut the little things shown in the picture - red arrow). The hole for the cooler is 30mm diametter. ... There are 5 holes to screw the bottom of the box (M2,5 screw) 4 holes for pressing the stack...

I also utilized an alternative LCD display, the MPI3508 3.5 inch model (I trimmed the small components shown in the picture - red arrow). The hole for the cooler measures 30mm in diameter. There are five holes to secure the bottom of the box using...

... in a subsection. You also need a soldering setup to connect the button to the wires, and you'll need a deburring tool to remove the tab from the inside of the hole in the switch cover base plate (USE GOGGLES AND GLOVES AND DON'T TOUCH YOUR EYES.

Experimenting briefly with using the ball & socket design from thing 3017729 to make the articulated arm, I discovered it difficult to print robust versions of those sockets in the metallic bronze PLA I wanted to use. Therefore, I crafted something...

... that the bowden tube and wiring were prone to getting snagged on the original mount. To address this issue, I've modified the design of V2, incorporating rounded edges that prevent it from sitting flush with the bottom of the 20x20 extrusion.

I'm eager to dive into this project, as it's specifically designed for the RPi 3B+, particularly with its four new Power Over Ethernet pins. It also happens to be compatible with the RPi 2B and 3B models, along with most Pi HATs. ...Could you let me...

This is a remix from https://www.thingiverse.com/thing:3839778 ℹ️Projekt: Teil1: https://www.youtube.com/watch?v=NKX0S9MPxS4 Teil2: https://www.youtube.com/watch?v=mW_v98ZZ0w8 Teil3: https://www.youtube.com/watch?v=kZimWP_M5w8

I made a 180° variant, as I wanted the top of the Pi4 to face away from the printer.It makes the GPIO, Camera and Display ports more easily accessible. It should also be compatible with Dual Fan variant of the Armor Case. I have not tested, but it...

The popular Raspberry Pi single-board computer is a great addition to many makers' projects, including the DIY Ender-5 3D printer. ...However, one of the challenges that makers often face when integrating the Raspberry Pi into their 3D printing setup...

I was searching for a larger case for the Pi that could be stood upright instead of laying flat, so I could accommodate a heatsink on the underside and potentially include dual fans with airflow slits on the larger faces. Larger openings are needed...

Austin3dprinting's STL files had some errors, so I re-did them. ...All of the arms now have a smooth inner profile, and the camera+final arm STL file is now split into 2 files so you can distance them on your printer.

My camera wouldn't snap into place because the hole was too small, so I expanded it slightly and adjusted its position upwards to get a secure fit.

This camera mount is designed for use with the Solid Bed Mount set produced by https://www.th3dstudio.com/product/cr-10solidmounts and a Raspi camera v2. The goal is to lower the lens so that the nozzle is more visible than it would be using the TH3D...

This is a remix of tobbi007's design, where I've introduced several key modifications. The top piece has been thoroughly altered, while the bottom component remains unchanged. ... Changes Implemented: RPI4 camera cable slot has been added RPI4 GPIO pin...

Austin3dprinting's STL files had some errors, so I re-did them. ...All of the arms now have a smooth inner profile, and the camera+final arm STL file is now split into 2 files so you can distance them on your printer.

Remix and add the honeycomb all the way across the design to enclose the fan. This adds a more clean look. I used this fan and it fits tight enough that you do not need to use screws to hold the fan in place. ... ...

I'm using a mix of different stuff I've found around here to keep things organized and make life simpler, it's working out great so far!

I decided to create a custom enclosure for my Raspberry Pi 2, an incredibly affordable and user-friendly Linux desktop computer that delivers excellent performance at just $35. To start the process, I chose to model the Pi itself rather than...

... hole for the USB-C entry, and changes the right-most port to accept a HDMI connector. How I Designed This I took the hole for the USB-C power entry, made it a solid, aligned a hole to the side, grouped it, then made the resulting solid "D" a hole.

Edit it online https://www.tinkercad.com/things/j4mshWYzBS2 Added a "D" keyed hole for the USB-C entry, and changes the right-most port to accept a HDMI connector. How I Designed This I took the hole for the USB-C power entry, made it a solid,...

Raspberry Pi 4 fans are supported by the following design: https://www.thingiverse.com/thing:4097379 For those interested in creating an Ender-3 station, I invite you to check out my previous project: https://www.thingiverse.com/thing:3700643 If...

... for solid material to be built around bolt standoffs. In my initial print, I failed to do this, resulting in the standoff pulling off. I've updated the lid STL to fill voids around the power plug, HDMI port, and 3.5mm jack as of November 29th.

... of my Ender 5 supports, but I couldn't locate one. ...This is intended to simply hold a Raspberry Pi on the printer (for OctoPrint etc) in place. The design fits snugly against the profile of the Raspberry Pi and elevates it about 10mm above the rail.

The ideal case should have several features: first, it must allow for unobstructed airflow; secondly, it should be equipped with a large fan adapter that can accommodate a 50mm fan; thirdly, it needs to provide adequate clearance from the ground;...