power supply cover 3d models
237362 3d models found related to power supply cover.thingiverse
Power Supply Cover V2, add Power switch and LED slot. ...Enjoy and have fun ^_^
pinshape
SummarySimple power supply cover 12V 51x94x42Print SettingsPrinter Brand: RepRapPrinter: mendelmax 1.5Rafts: YesSupports: NoInfill: 20%
thingiverse
This is a remix of the power supply cover created by IsmaelPR1. ...I added a bracket onto the left side so the left side could be tied or bolted to the stock power supply cover
thingiverse
Power supply cover. ...Print Settings Printer Brand: RepRap Printer: Sunhokey Prusa i3 2015 ...
thingiverse
This is a plug and play power supply cover. ... Before printing take care the dimensions because it was designed for a small power supply.
thingiverse
This a power supply cover for the Hictop 3D printer, it adds a power switch and I standard power connector to eliminate the from the wires.
thingiverse
Power supply cover with location provided for 3-Pin-IEC320-C14-Inlet-Module-Plug-Fuse-Switch-Male-Power-Socket-10A-250V. ...Rounded corners.
thingiverse
A power supply unit cover protection against electrical shock. ...PLA Layer height 0,300mm Infill 15%
thingiverse
This is an ATX power supply cover to build your own laboratory power supply. ... It uses the ATX power supply standard size and you only need some long screws to fix it and some banana connectors.
thingiverse
Remixed power supply cover from neildonn, adjusted to a spare power cable + switch that I had on hand: - removed power socket - added a hole for the mains power cord - thicker bearing walls - longer opening for the power switch
thingiverse
Power Supply Cover for ____ power supply. This cover makes it possible for A IEC socket to be fitted for ease of plugging in AC power to this supply. ...Along with the socket there is a rocker switch and a 7 segment that reads the DC voltage coming out...
thingiverse
Snap-on Bukobot Vanilla 8 power supply cover with power switch hole. No tools and no cable disconnection need for installation - just route cables through open slot and push in! ...Made with Tinkercad.
thingiverse
a simple power supply cover if you have to run the wires UP not BACK from the rail (i did not found anything like that so I have to design my own )
thingiverse
To mount the cover to the power supply, the following non-3D printed parts are required: M4 x 8 socket head cap screw - qty: 3 M3 x 10 flat head cap screw - qty: 2 M3 Heat set insert - qty: 2 These are the M3 heat set inserts I used:...
thingiverse
A power Supply cover for the standard 49x113 switching power supplies. It allows me to mount the power supply flush on the right side of my Prusa i3 re-reworked frame. There is an indent in the box that makes room for the nuts that hang out for the...
thingiverse
This is power supply cover for MeanWell (or similar type). I designed it for protection of power supplies for LED lighting, where i use these industrial power supplies for their performance and reliability. Customizer variables are described in...
thingiverse
This is a power supply cover for a Cosel 24v 4.5amp power supply that has the dimensions of 2" x 2.7" on the end. ...There are two holes: one for the switch/cord/fuse and the other for the power out connector.
thingiverse
it is a power supply cover for a chinese 24v30a power supply. the bottom screws don't line up i didn't calculate it well i just used some tape instead. it take standard cheap banana connectors and kinda standard 3d printer powersupply plug...
thingiverse
I was recently looking for a power supply cover and noticed that there was no covers that had both the right connector and a lot of XT60 ports. So I designed my own. It has plenty of ventilation, 6 XT60 female Connectors and is quite robust. And...
prusaprinters
A power Supply cover for the standard 49x113 switching power supplies. It allows me to mount the power supply flush on the right side of my Prusa i3 re-reworked frame. ...There is an indent in the box that makes room for the nuts that hang out for the...
thingiverse
There is already a lot of power supply covers on Thingiverse, but nothing that can really satisfy all my needs. So I designed my own. My power supply is a 24v one bought on Aliexpress. But its size is pretty standard (50*115mm) so it should fits...
thingiverse
Power supply cover printed in flexible PLA. I designed this to protect a standard 20A PSU mounted on the back of a speaker enclosure. At 160mm wide, it covers most of the thin stamped metal portion of the box. Would be a nice addition or remix to...
thingiverse
This is a power supply cover for our geetech MeCreator. It was designed that no cutting wires is needed, just any small two screws . To make it more interesting we designed it like a face with a strange smile (mounted with two buttons) and a hair...