pps 43c 3d models
271 3d models found related to pps 43c.thingiverse
A simple spacer block for the inside of a 9mm pps-43c to fill up the gap where casings like to collect and cause issues. No guarantees on durability of your plastic parts in a hot gunpowder environment, but it has worked for its intended use. ... ...
prusaprinters
PPS - deco for the youtube videos that I made for the Pawpet-Show channel Category: Decor
cults3d
The two main models of this gun, the PPS-42 and PPS-43, were used extensively in the Red Army during the second world war , along with other versions of this gun was widely used in socks. ...both the Warsaw Pact countries as well as many African and...
grabcad
This is my proposal for Antigravity's new PPS exterior case. This simple, sleek case is made up of two smooth, gently curved, black injection-molded plastic halves. Logos and lettering can either be projected onto the face of the shell or simple...
cults3d
Einfacher Ständer für PPS Shotgun Shells. ...Es passen auch CO2 Kartuschen rein;-)
thingiverse
Einfacher Ständer für PPS Shotgun Shells. ...Es passen auch CO2 Kartuschen rein;-)
grabcad
My second entry to Antigravity Batteries Challenge: https://grabcad.com/challenges/antigravity-batteries-challenge PPS Concept 2: - Black color body with yellow or red lines. - Colored or aluminum end front and rear covers. - Input...
grabcad
Bolt for PPS-43. Using this to model different ways to convert a bolt to semi-auto only. ...This is the as original, FA design.
thingiverse
... We are Duchenne type muscular dystrophy patients. We use PPS switch, but pneumatic switch can not be used well. Therefore, I made small air pressure sensor parts. ... This 3D part uses a small finger coat.
cgtrader
The PPS and its variants were used extensively by the Red Army during World War II and were later adopted by the armed forces of several countries of the former Warsaw Pact as well as its many African and Asian allies. Operating mechanism The PPS is...
cults3d
This is newest version of my shotgun pistol which uses Airsoft PPS gas shells to shoot 1-6bb at once. It can be very fancy moment to "clean room" with this, you can use its like tiny 40mm launcher as sidearm or add barrel for tighter spread. This...
grabcad
Another entry for the Antigravity PPS MicroStart XP-1. I've added a few subtle curves and a pattern on the top. The cover for the 12V jumpers are once again at the front of the case and accessed by peeling open the rubber flap. ...The location of the...
cults3d
1/35 Russian PPS 43 unsupported Please be aware you will need to add your own supports to achieve desired orientation.
myminifactory
This is a magazine loader specifically modeled for the single stack Walther PPS M2 Magazine 9mm. ... Print Upside down, with at least 4 walls and 4 floor/roof, and 50% infill, it must be strong for the spring.
thingiverse
Re-creation of the loading tool that comes with the PPS airsoft shotgun shells. Print Settings Printer: Wanhao i3 v2 Rafts: ...
cults3d
Most importantly, PPS gas shells. I haven't tested the design with 6 BB metal shells made by other manufacturers so I can' guarantee those would work but if you want to be sure pick up the version of this design with .STEP files and adjust the...
sketchfab
Soviet submachine gun developed in the caliber 7.62x25. Used extensively by various communist countries during the cold war. ...Revered for its dependability and simplicity.
grabcad
The model is created for adaptation for paper modeling. Separate thanks to the author of drawings "СПетрович". ...Thanks to the test collector "droganov1973".
thingiverse
PPS/TANAKA M870 QUICK RELOAD SHOOT Please use epoxy glue
grabcad
folding stock to upgrade for the PPS-43 submachine gun that comes with a fixed wooden stock.
thingiverse
It's just a small DIY project to me, which serves to hold extra shells on my Airsoft PPS M870. ...For fast and solid installation and removal, 3M Dual-Lock tape is used instead of conventional Velcro tape.
thingiverse
This is a magazine loader specifically modeled for the single stack Walther PPS M2 Magazine 9mm. Print Upside down, with at least 4 walls and 4 floor/roof, and 50% infill, it must be strong for the spring. ...
thingiverse
Model of landing gear indicator PPS-2M. ...Dimensions and radiuses are 100% correct, taken personally by me from a vintage new old stock real landing gear indicator, that i have bought so you do not have to :D
cults3d
Hardware Needed: Handguard - M4x25mm Countersunk Bolt and M4 Nut - Two M3 x 220mm steel rods as support (Optional) - M6 x 35mm Steel Dowel Pin (Replaces old pin from old barrel, this sits flush with the handguard and acts as another point of contact...