practical uses for a 3d printer

I needed a way to compare one side of the z-axis level to the other side on my 3D printer as it droops when the steppers are powered off. I ordered parts to link the z-axis lead screws together however in the meantime, this tool makes it easier to...

I needed a way to compare one side of the z-axis level to the other side on my 3D printer as it droops when the steppers are powered off. I ordered parts to link the z-axis lead screws together however in the meantime, this tool makes it easier to...

I needed a way to compare one side of the z-axis level to the other side on my 3D printer as it droops when the steppers are powered off. I ordered parts to link the z-axis lead screws together however in the meantime, this tool makes it easier to...

Instructions Print four corner pieces, use wood for the the bottom, the sides and the top with the top a thickness of 12 mm. If you want to use the spool holder get some M8 rods (or similar size) and 6 nuts and screw them into the corner pieces at...

I have no printer yet, but did this model some time ago and I hope somebody print it and I can see the photos of the real thing! Im not sure the model is printable, tell me what i got to have in mind to make it compatible if is not. Thanks so much. ... ...

This is a support for pen-can use your 3d printer as a plotter in no time

Very simple lighting for a 3d printer. ...I used 12v led bulb (socket G4).

This support is meant for the heated bed of a 3D printer. Use one on every corner of the heated bed and mount it to the bed of the printer. On the underside of the base is a space where a small M3 nut can be placed for the M3 bolt that holds the...

Drag knife for a 3d printer/ bearings 6x16mm and rod size 6mm Print Settings Printer: miller/home made Rafts: No Supports: No Resolution: 0.2mm Infill: 40% Custom Section

Easy 1 hour print, should fit all Bambu lab printers. ... re-use of original spoolholder. Can hold a 1 kg spool, for heavier spools adjust infill and or material. ...

 To be used in a 3D printer a protective case and mounting system are required.I designed a case where the camera stick is attached with two 4mm M2 screws using hot inserts.  The stick acts like the back for the case.  The stick has...

But I couldn´t find a Spool holder for the A-3 printer (I bought from Amazon Germany) this is my first project in Fusion360. I could not realize all my wishes, so this project will change from time to time, as I wish a wider base to get more...

For 2020 Aluminum Profiles - it slides on. ...For switch you may need a 20/18mm round of/off rocker switch, as a light you could use a 12v LED GU 5.3 lamp.

... You run your printer using Repetier Server on a Raspberry Pi, then use a python script to connect to Repetier Servers API and extract the time remaining of the current print job and then send that via serial to the Arduino that controls the clock.

Post-Printing Because I use the .STL file (that was all that was available at the time), there is a small artifact at the top that I had to file off slightly. Other than this, all should be good. How I Designed This Partly done using Onshape and then...

Feel free to download it ;) Give me a feedback and if you have some questions or comments message me please :) Just one more thing, the file has an author name and an e-mail that is related to the person that do the file, so don't worry, and you can...

It is recommended to use a M4 thread tool in the hole for mounting the 7x7 mm cable chain. M4 nuts pressed into position by a tool. M3 nuts pulled into position with a screw and washer. It is a good idea to heat up the carriage on the hot bed before...

it can be seen working here:https://www.youtube.com/watch?v=KB8H-T4nDkI Its a simple geared system so there is alot of backlash but its not made for precision dispensing. The secondary gear has space to press fit 625zz bearings. Modification on the...

I wanted to use the hinges here:- http://www.thingiverse.com/thing:1187867 but after printing the two halves, I couldn't get them to mate together properly, because they were way to tight. So I modified the original STL file, to make a thinner hinge....

Как сделать поворотный столик для видео на 3D принтере? Поворотный столик состоит из напечатанных на 3Д принтере: - основания диметром 300 мм (или 200 мм); - ведущей шестерни; - ведомой шестерни (или магнитного основания); - стоек для плат; -...

... using the threads. Threaded inserts have been included in the design to hold the components. According to the production quantity and the equipment available, these can be added either before molding (Insert Molding) or after using heated shafts.

This is an alternative carriage for a Eustathios Spider 2 3D printer that uses m8 linear bearings instead of bushings. This can reduce friction, cost, and wait for parts. But the original carriage works fine too. Note that this carriage was reduced...

Here is a calibration for xyz，you can zoom in/out to fit your printer size. The length is 102mm by default. It can be used to calibrate angle deviation and step deviation. ...The block notch identifies the XY plane.

This was designed to hold large spindles of fibre for storage, it may be a bit of an overload but in my testing the chopstick is the weak part, even with only 2 layers (1.2mm shell .6mm layers), it breaks at the chopstick. I'll add some more...

This was designed to hold large spindles of fibre for storage, it may be a bit of an overload but in my testing the chopstick is the weak part, even with only 2 layers (1.2mm shell .6mm layers), it breaks at the chopstick. I'll add some more...

Graphic Design 3d for Multi-uses an eps file

Pikachu for printing on a 3D printer

A thick 2d Plane I used for a Schlieren practical. ...This is an experiment where you can visualize airflow using a light, concave mirror, a knife, a camera and a lens (if your camera does not have one)

 The conversion of the 3D printer into a plotter has also been successfully used to generate printed circuits, the circuit is designed, the gcode is created with flatCam and the copper base is colored with permanent marker. By placing a punch as a...

An accessory to convert the 3D printer (Creality Ender 3) into a cnc machine. Currently the accessory used is a Bic pen. The pen holder consists of three parts: - A base, connected to the fixing screws of the printer's fans. When the printer is used...