precision syringe dispenser 3d models
32316 3d models found related to precision syringe dispenser.thingiverse
If you have the need to dose in a precise small amounts of liquid or viscous material. Each turn of the knob corresponds to 1 mm piston displacement with thread M6. ...Print Settings Printer Brand: Rostock ...
thingiverse
This syringe dispenser clips onto a standard 2.5cc syringe and lets you control where the plunger should stop with each press, to limit the volume disbursed and give you finer control. It's composed of 3 small printed parts, which are very easy to...
thingiverse
Solder paste syringe dispenser, based on a design I found on the internet https://www.youmagine.com/designs/manual-solder-paste-dispenser I altered the design so that it is easier to print and assemble. YOU NEED: 1 x M5 nut 1 x M5 threaded...
thingiverse
A stand to hold three syringe dispensers for solder paste, flux, etc. Each has a small pot to hold a tissue or sponge for tip cleaning (or tip storage?). ... There is a version with angled 10 x 10 x ~70mm slots on either side for holding tweezers...
grabcad
Syringe holder with electronic dispenser. ...Freely inspired by the possibility of anticovid vaccine doses.STP 214 -Parasolid x_t
thingiverse
If you need to dose a precise small amount of liquids from syringe this is the perfect thing. 1 knob turn = 1 mm piston displacement. ... 1pcs x 85mm M6 bolt 4pcs x 35mm*4mm bolt(or screw) 2pcs x M6 nut
thingiverse
The slot in the body to hold the syringe is 25 mm wide instead or 35 mm to fit the smaller syringe. The body and knob are the same size as evgs, except that the nut is threaded for M8. I wanted these two parts about the same size as the evgs...
thingiverse
This is a clamp to hold the paste syringe to the case. ...Original:http://www.thingiverse.com/thing:384680 Made:http://www.thingiverse.com/make:89888
thingiverse
Improved syringe clamp for the Solder Paste Dispenser. ...Designed to fit 10cc Dispensing Syringe Barrels.
thingiverse
MANUAL SYRINGE GUN FOR FLUX VALVE DISPENSER Use M3 screw
thingiverse
changed the original design a bit so it is better to print (chamfers instead of roundes corners) and an M4 hole for a grub screw to hold that syringe in place and stabilize the whole system. I have now 3 of these in use and they work absolutely...
youmagine
This is a clamp to hold down the syringe for Geir's Solder Paste Dispenser posted at Thingiverse.http://www.thingiverse.com/thing:384680
cults3d
Syringe Dispenser Tapered tip luer lock for the cerambot clay 3D printer. ... Nozzle sizes : 1.5mm 2.0mm 4.0mm 6.0mm
thingiverse
Syringe style swedish loose snus dispenser, size about 3ml. Tolerance is only 0,1mm between inner and outer part so high resolution is needed. I have been using this for 3 days now and seems to be working fine without gasket. Might start to leak...
thingiverse
http://www.youtube.com/watch?v=HHdTIGn8umk Also on the market the liquid dispensers for aquariums are very expensive, and the cheap ones are not reliable. I just made this version 1 of the Syringe dispencer, that I will make two pieces controlled...
cults3d
http://www.youtube.com/watch?v=HHdTIGn8umk Also on the market the liquid dispensers for aquariums are very expensive, and the cheap ones are not reliable. I just made this version 1 of the Syringe dispencer, that I will make two pieces controlled...
thingiverse
Manual Syringe Gun for Foot Flux Valve Dispenser Use M3 screw
thingiverse
this version of syringe dispenser its smaller but stronger and stabiler as my first design.
thingiverse
Taking inspiration from [Albert van Dalen's Spoty precision micro-dot](https://www.avdweb.nl/tech-tips/pcb/solder-paste-dispenser) and the [Micro-dot Solder Paste Dispenser for less than $2](https://www.thingiverse.com/thing:4865220) by @eleotlecram...
thingiverse
Ремикс только для флюса, прочность конструкции ниже. Для паяльной пасты не подойдет! Шпилька 6мм основная, и в качестве оси ручки шпилька 3мм. ... Толкатель оригинальный.