presta cap 3d models

Presta valve cap with internal thread. This model is a little bigger than the standard ones, but it is resistant (it's been more than 6 months that I installed mine on my bike and they have not moved). ... Cap for Presta valve type with internal thread...

If you have ever lost the little core tools or needed to fill you tire with sealant on a ride, then print this little thing. ...It is a combination Presta valve cap, core removal tool and valve extension wrench.

It's a presta valve cap that is a peanut

This is a presta valve cap. ...Though it was designed with resin printing in mind you should be able to print it with and FDM printer as long as you use a small layer height, .1 to .05.

Combination of two models from Thingiverse:Middle Finger Schrader Valve CapPresta Valve CapThis is the first iteration of this design, made in a few hours pretty roughly. Threads came out pretty nice with no supports inside the valve (on the...

Cap presta for bike

I made a valve cap for my cannondale presta valves. ... Enjoy.

This is a remix of the Schrader car / truck valve caps to fit the common Presta bicycle tyre valves. (remix from https://www.thingiverse.com/thing:5471630) I defined the UNC #12-24 TPI threads and added these to the 'middle finger'. The valve caps...

Replacement cap for Presta/Racer bicycle valve. Precision of the threads may depend on the printer and printer settings. The threads are, on purpose, a bit loose. ...I have successfully printed this with a 0.4 mm nozzle and 0.2 mm layer height.</p>...

Replacement cap for Presta/Racer bicycle valve. Precision of the threads may depend on the printer and printer settings. The threads are, on purpose, a bit loose. I have successfully printed this with a 0.4 mm nozzle and 0.2 mm layer height. It...

This Merida branded valve cap goes over the entire presta valve stem, giving your bike a clean look. The threads are modelled as M6 with a 0.8 mm pitch, but still I had to scale the valve cap with 98% in my slicer. Thus, you might need to experiment...

This Merida branded valve cap goes over the entire presta valve stem, giving your bike a clean look. The threads are modelled as M6 with a 0.8 mm pitch, but still I had to scale the valve cap with 98% in my slicer. Thus, you might need to experiment...

This Merida branded valve cap goes over the entire presta valve stem, giving your bike a clean look. The threads are modelled as M6 with a 0.8 mm pitch, but still I had to scale the valve cap with 98% in my slicer. Thus, you might need to experiment...

This Merida branded valve cap goes over the entire presta valve stem, giving your bike a clean look. The threads are modelled as M6 with a 0.8 mm pitch, but still I had to scale the valve cap with 98% in my slicer. Thus, you might need to experiment...

It doesn't cost you anything extra, but helps me out a lot :) Print instructionsCategory: Sport &amp; Outdoors Summary This Merida branded valve cap goes over the entire presta valve stem, giving your bike a clean look. The threads are modelled as M6...

Designed for any presta valve. Printed in 0.16mm layers, with full supports and sliced using PrusaSlicer. TPU or rubber material is recommended so it wont break as easily. ...

... one of these before? ...I sure have! Now you can 3D print replacements! I have included threading that allows the cap to screw on to form a snug and reliable fit. ...Tolerance is included to accommodate for the inherent inconsistencies of 3D printing.

I have included threading that allows the cap to screw on to form a snug and reliable fit. Tolerance is included to accommodate for the inherent inconsistencies of 3D printing. ... UPDATE: 3/5/18 Thickness issue fixed where threading meets top UPDATE:...

I have included threading that allows the cap to screw on to form a snug and reliable fit. Tolerance is included to accommodate for the inherent inconsistencies of 3D printing. ... <b>UPDATE: 3/5/18</b> Thickness issue fixed where threading meets...

Also the cap keeps dirt and rocks away from the valve. Print it to match your bike colors and share your picture ! ABS 0.2mm No support MakerGear M2 https://www.instagram.com/demian.villanueva/https://www.facebook.com/demianvillanueva/ . Print...

Wanted a cap that sat a little firmer on, as they tend to fall off, or crack when you try to make them sit well. Recommends printing with maximum 0.1 layer height. Printing multiple at once is no problem. Remember dry filament.</p> <p>I also included...

Presta cap with core remover on the opposite side. ... Printed using PLA at 100% infill

Presta valve cap with core remover on opposite side. ... Print using PLA at 100% infill.

Tried to print the Presta valve cap by Elliott_Turner but it caused too many retractions because of the knurled part which led to gaps in the final print. ... So I decided to simplify it by removing the knurling making it easier much easier to print.

Borrows shapes and ideas from the two source things to make a more trim version of a Presta Valve Cap that clips onto a spoke while you are filling your tire. (Note: I listed two sources for the inspiration and shapes that I combined to make this...

NHL teams cap for presta valves. Self threads when putting it on the valve. Currently has Montreal Canadiens, and Detroit Red Wings. Working on adding other teams Future Plans: 1. Add remaining NHL teams 3. ...Make design for Schrader Valves

Adapted from Droppunk design: https://www.thingiverse.com/thing:3226687 Part of my valve cap collection: https://www.thingiverse.com/xxmtx/collections/38672306/things Added a schrader valve (and compatible with a presta adapter), and a hole for a...

Part of my valve cap collection: https://www.thingiverse.com/xxmtx/collections/38672306/things Tolerance are pretty tight, you need to form the thread, first time you screw it to the valve. ... Presta adapter is avaiable here:...

A valve cap for a Presta bike valve featuring one of the two lighthouses from Cape Arkona on Rügen island, Germany. ...The print was used as a giveaway for the participants of Bikepacking Trans Germany (BTG) that finishes at the Cape.

Part of my valve cap collection: https://www.thingiverse.com/xxmtx/collections/38672306/things Added a schrader valve (and compatible with a presta adapter), and a hole for a necklace mount. V43: Added a longitudinal hole, allowing breathing if...