primary arms 3d models

... ...I created this sunshade and flashkill to fit over my Primary Arms 4-14X FFP scope. Light sanding required to get a snug fit. Flash kill designed to friction fit into the sunshade. Interior stops added to align flashkill when inside the sunshade.

with tiny arm computer resting on a sheathed sword carrying something sideways (gun or mine) with and without handle pointing/aiming with pistol pointing with index finger tactical pointing with two fingers pointing without hand so you can attach a...

Throw lever for Primary Arms 1-6x SFP scopes. This is an original design. **TABLE OF CONTENTS** - Parts - Printing Details **PARTS** - (1) M3x12mm socket head screw - (1) M3 nut **PRINTING DETAILS** - Settings (Tested on ender...

One arm pointing up and one holding the gun to the side (to reload or to show of a gun that might have been craftet by a master of something) Presupported armcake included. ...I'm new to supporting so it might not be the most elegant thing but it...

Primary Arms throw lever. 2.5-10x. ... Will need nut+ screw

I wanted an anti-reflection device (ard) for my primary arms 2.5x prism, but primary arms doesn't offer theirs anymore. This is designed to slide on and off but fit snug so that it shouldn't come off on it's own. The one pictured is printed out of...

Cat tail lever for the Primary Arms 4-14x FFP scope. Printed with no supports. It's fairly chunky because my PA 4-14x has an extremely stiff zoom ring. This works on both the non-illuminated and the illuminated versions. ... Note - as a couple of...

It was designed to fit the Primary Arms ACSS Raptor 1-6 FFP Scope. When printed using ABS, it did not take any scaling for me. I printed the part at 100% infill, used sandpaper to carefully round all the edges, and then did an acetone vapor...

Re-mix from the throw lever by jitblass. I fixed the messed up geometry, beveled the edges (so you don't have to sand them afterwards), and shrunk the cutout for the nut to accept standard M3 nuts. Once printed, you'll need a M3 x 10 screw and...

I have not use the screw hole version yet but included it, the file without the hole has held up to a few range trips so far. Still first prototype will continue to improve if failure occurs. ... Might work with the SFP version don't have one to...

A bit tight fit for Primary Arms Micro Dot Gen.1 and Holosun 401 series. You can scale if for 0.5% upwards if needed. If you have a well-calibrated machine, then it's drop-in. Use as fine resolution as one can. ... "It's intended to protect lens...

I'm adding this as it has been requested by a few people. This is a Cat tail for a PA 1-6 SLX Gen 3 (not sure it will fit Gen 4 or ones with factory removable cat tails).. This also requires a small cap head screw and nut to use. ...It's been so long...

update 2020-10-15: I removed the original smaller lever ring. The gap at the screw was just too big, I didn't like it. Remixed a couple and made the lever a little shorter so I don't break it in my bag. Also used m3x14 and an m3 nut. Sorry...

Note: The model is for professionals who know how to use it correctly. Avoid the case that the customer does not know how to use it after purchasing the model and then blame the defective product. Because digital products will not refund. Customers...

Hello all! ... Here is the file for the Tactical Warsuit Weapon Arm Joint!  Build this into the other arm that comes with the model so you can use both weapon options instead of using magnets!!! Cheers! ... -N

The parts i used: Head: Primary Builder Arms: Primary Builder Bolt Rifle: Primary Builder Legs : https://www.thingiverse.com/thing:3995722 by feanor007 Belt: https://cults3d.com/en/3d-model/game/space-warrior-belt-accessories by mrmcangry Chest:...

Customized version of http://www.thingiverse.com/thing:138222 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=138222

PRIMARY FILTERS

primary weaving in super conventional LOOM

Belt Primary for a Softail EVO drive train

Primary School Designing For My Sophomore Bachelor of Architecture.

I myself printed both spool parts, knob, stopper handling thingy and the “Primary reel guide no holes” and “Primary reel handle without holes for guide” together as an assembly. Then I made the long guide hole later. Maybe not the smartest...

arms

arm

Arms

Wanted to stay in practice by modeling an arm, then I sort of just kept going.

http://www.thingiverse.com/apps/customizer/run?thing_id=27468 Instructions Using the following options: target_side = 104 Gear_Stages = 1 Gear_Play = 0.2 Gear_Teeth = 10 Screw_play = 0.1 hand_length = 41 arm_width = 8 assembly = 4 show_target = 1...

http://www.thingiverse.com/apps/customizer/run?thing_id=27468 Instructions Using the following options: hand_length = 30 show_target = 1 assembly = 4 Gear_Stages = 1 target_side = 50 Screw_Size = 3 plate_thickness = 3 Grip_pos_r =...

Just a version of the arms with less vectrice (Decimate geometry with blender) and in STL format. ... Thank you for the original design!!!!

Primary Cover Allen Bolt