print 3x5 cards 3d models
1243096 3d models found related to print 3x5 cards.thingiverse
Simple remix of **Index Card Holder** by **HamOP.** I resized the models to fit more common US 3x5 index cards, as well as adding a hex grid to the bottom to allow for faster prints with less filament.
thingiverse
A Frame as HPDA for 3X5 cards. Makes the outer cards acsessibel for writing and reading. and has a Integratet "TODO" card holder slit. ... A 5 pictogram section on the top for easy categorising for Exapel: Note | Task | Important | Address |...
prusaprinters
They needed to be easily accessible and organizable and I wanted the box to be held tightly shut by hidden magnets embedded into the design. The hinges I also wanted to be printed in place - being small while still sturdy enough to withstand daily...
thingiverse
There wasn't anything like this on Thingiverse so I made my own. ...It is a notecard holder that fits perfectly holding 1 stack of traditional note cards. ...The top fits perfectly flush to the body making it seem like one solid object.
thingiverse
Use this print spacer to print 3X5 index cards from your brother laser printer note: the revision2 has a relief to adjust the rear paper adjuster
thingiverse
I stick 1/2" round labels onto the card and then match that card to its appropriate 3x5 holder. Happy organizing. Note: These print vertically without supports. You might need to trim a strand or two at the top of the large opening. ... ...
thingiverse
Customized version of http://www.thingiverse.com/thing:797089 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=797089 Instructions Using the following options: thk = 3...
thingiverse
This is a 3x5 card holder to be used with the pegboard shell for the Bambu Lab p1p. ... The left 3d model is for the left hand side of the printer as you face it.
thingiverse
This is a remix of FelixNovember's "A8 Index Card Box for 60 Vocabulary / Studying Cards", I sized it up to fit 3x5 index cards and made it a bit slimmer. This fits around 50 cards. ...The lid is a bit snug, so I will be uploading an updated version...
prusaprinters
So here is the next monitor storage device, a 3x5 card holder that hangs over the back of my monitor. It can be printed without support if you print it upside down. I made the inside of the base with a large incline to make it easy to grab the...
thingiverse
It is available here: https://www.thingiverse.com/thing:4194714 I use a 3x5 card each day to list out my tasks and they have also been getting either misplaced or in the way. So here is the next monitor storage device, a 3x5 card holder that hangs...
cults3d
Holds about 100 typical index cards snugly, more if you let the top float up. Prints without support. Top is a bit loose to ensure it'll fit with any printer. Secure with a rubber band. This thing was made with Tinkercad. ...Edit it online...
thingiverse
Holds about 100 typical index cards snugly, more if you let the top float up. Prints without support. Top is a bit loose to ensure it'll fit with any printer. Secure with a rubber band. This thing was made with Tinkercad. ...Edit it online...
prusaprinters
I took measurements from his STL, and recreated a space for a microSD instead of the big size.I recommend printing some of the larger ones too, so you have some storage for the adapters.I managed to print these as oriented, with a 5mm rim and a 0.4mm...
thingiverse
I recommend printing some of the larger ones too, so you have some storage for the adapters. I managed to print these as oriented, with a 5mm rim and a 0.4mm nozzle at 0.2mm height. ...The overhand on the window always sucks, but it can be trimmed...
thingiverse
A simple 3x5 card and pen holder. ...Mount on the wall or set on your desk!
thingiverse
This is a suggestion box that will fix 3x5 inch index cards. There are two files. One will print with the large piece oriented upright. The second file has the large piece on it's side so you can easily add text to the face of it. Customized...
thingiverse
Customized version of http://www.thingiverse.com/thing:53561 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=53561 Instructions Using the following options:...
thingiverse
Customized version of https://www.thingiverse.com/thing:3688335 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3688335
thingiverse
So I needed to mount a 3x5 index card stamp i made for Pathfinder Initiative Cards on something, so I made this stamper. ...I'm new to tinkercad and designing in general, so figured this was simple enough to get my feet wet.
thingiverse
... Great design to use for studying, homework, flash cards, and more. Blank cards used: https://www.amazon.com/gp/product/B07X5CSNVH?ie=UTF8&psc=1&linkCode=sl1&tag=rdotkraz-20&linkId=19849a9dd42061a498cb631ec6b0da67&language=en_US&ref_=as_li_ss_tl
thingiverse
A remix of a design made by user Schoonology. ...I increased the x and y lengths of his model to accommodate 3"x5" index cards. However, the angle of the portion that displays the card might be pointed too far back for some people.
thingiverse
... The second model is the grate with an edge, so essentially the grate will have a little lip on the top making the edge of the grate a bit higher that the Styrofoam (this is a tricky print, i would print it sideways with support in the middle. ...
thingiverse
... on your material of choice as this is a large flat surface and you may damage your bed if you use too much force trying to remove it. Print Settings Printer Brand: LulzBot Printer: Mini Rafts: No Supports: No Infill: 20% Notes: Use release agent
thingiverse
This holds 3x5 paper cards and has a slip on lid. It has a divider. ...It should be easy to print.
thingiverse
This 3x5 sized tray will hold SD cards securely in a office 3x5 card box. Place in a zip-lock snack bad and SD cards are safe for transport in a bag without dumping all over. ... Hole in the back permit removing SD cards with fingers.
thingiverse
The original card of the toy shop was lost so we (mom/dad) got new, personal ones. This is a multicolor print with different colors in one layer! Split the STL in single parts an assign the (virtual) extruders with the different colors. ...I used the...
thingiverse
Organize those USB drives in a 3x5 card box. Plug in your USB sticks and insert in the box for safe keeping. ... See the SD card holder that works with it.