print benchy with or without support 3d models

The print quality, which was achieved using PLA material with a 50% infill, yields a surprisingly flexible product that securely grips the phone. ...This design takes inspiration from other tablet stands I've seen here and gives it a fresh spin for a...

I designed this thing to place my laptop behind the monitor whilst still using the monitor arms.If the monitor does not have the vesa mount flush with the monitor surface you can use the spacer.  The position of the laptop monitor is not ideal for...

It have a 0.5mm clearance for work with almost every 3d printer! It is Scalable! If you want to scale down, watch for your own 3d printer clearance (mine is 0.3mm, so 40% down it would be able to spin freely) If you want to scale up, the clearance...

The belt clip for AOR/YAESU AR-DV10, YAESU FTA-550/570. ...Substitute for SHB-11. Designed in OpenScad, source files included. Print it, add 2 pcs M2.5x10 with washer. ...Callsign can be updated in SCAD file, then render new STL file.

Little Jeep Car for Print in Place !!!It have a 0.5mm clearance for work with almost every 3d printer!It is Scalable!If you want to scale down, watch for your own 3d printer clearance (mine is 0.3mm, so 40% down it would be able to spin freely)If you...

After printing, I read the directions... It did not fit my thicker 2017 frame. I widened the holes for the frame and thickened the base. Also, the bearings did not reach my screw rods to I included under mounts for those. Removed the top slots...

... parts. You can also put some glue between the clampbody and the base if you need to You can use rubberbands or springs if you prefer them more. IMPORTANT: The clamphead is a single piece, use the slicer to split it into two parts. ...

Bracket for the leveling sensor 18 mm, the fan and the x-endstop switch.I added a cable fix point above the sensorThe back cover for the fan is for hiding the cable which comes out of the back of the fan.I added the X-Endstop to the mount because my...

Bracket the leveling sensor 18 mm, fan, and x-endstop switch in place.\r\nA cable fix point was added above the sensor to keep things tidy.\r\nThe back cover for the fan conceals the cable coming out of its rear.\r\n\r\nThe X-Endstop is now attached...

A funny candle holder, print at 200%, if you wanna use those small candles that have metal rings around them print the mini candle stand at 190%.

Customized version of https://www.thingiverse.com/thing:3980956 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3980956

Customized version of https://www.thingiverse.com/thing:3980956 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3980956

Customized version of https://www.thingiverse.com/thing:3980956 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3980956

Customized version of https://www.thingiverse.com/thing:3980956 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3980956

Customized version of https://www.thingiverse.com/thing:3980956Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3980956

Customized version of https://www.thingiverse.com/thing:3980956 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3980956

If you want to go that route, use screws with a diameter of ¾" (19.05mm) to fit the countersunk holes. “This sucks, you have so many changes to make!” - also youI have included the source for the model (made in Onshape), but Printables only...

AM8 SKR V1.3 Board Holder Available With Optional Pi 3 Board Accommodation

... to fit seamlessly where old ones did. These tokens print rapidly and are extremely convenient to have on hand. They consume minimal filament during production. I tested mine at ASDA, and it functioned flawlessly. ... Speed: 50mm/s Infill: 100%

After printing, I examined the directions and discovered that they did not accommodate my thicker 2017 frame. To resolve this issue, I enlarged the holes to fit my frame and reinforced the base for added stability. Additionally, the bearings did not...

Customized version of https://www.thingiverse.com/thing:1196138 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1196138 Instructions Using the following options: figure = cube long_boy = 40 Secret = true haut_boy =...

I recommend using pigtails with connectors for wiring so any part could be easily removed if you need to work on the printer in the future. I used two pairs JST-SH style pig tails and JST-XH style pigtail with a connector: - XH connector soldered to...

... those that were initially crafted from pot metal, which over time had suffered corrosion and disintegration. ...Additionally, I designed it with a 15mm hole and a slightly thicker top section in order to securely hold a solar-powered light fixture.

After customizing the 3DBender Adjustable Stand by 3DBender for my iPhone X Max, my wife asked me to create one for her work iPad with a thick case on it. So I enlarged the entire stand and widened the area where it sits, also cutting out some of...

BOX WEED.CONTENDOR WEED GRINDERKING EASY PRINT WITHOUT SUPPORTS FMD OR SLA. 100X100X90MM EASY PRINT OPTIMIZED FOR FDM OR SLA. ...FILES FOR PRINTING WITHOUT SUPPORTS INCLUDED.SCALABLE TO ANY SIZE..MORE STUFF IN MY PROFILE...PRINT AND ENJOY.

... structure for its ability to resist torsion in certain parts. Total printing time: 1h37 Check out this video: https://youtu.be/671NCBFebXE For more information, visit: https://www.genapart.com/2017/01/02/catapult-printed-assembly-sans-support/

I just added Benchy. (And I scaled the model up--so if you want it super tiny again you will need to scale it down in your slicer) This is just modified of the completed file in the zip. https://www.thingiverse.com/thing:4441076 presented a...

Non-Hydrometer lid print with closed side down and Hydrometer lid print with grip side up. UPDATE 7/1/2020: Added ContainerSmall, a shorter container for thinner spools. I remixed this design to eliminate supports. This change reduced the print time...

The printable Goomba is designed without support necessary. It is split into two parts, thus requiring some glue to join it securely. A modification was made by user 7777773 of the original Little Goomba model. The changes included: Firstly,...

This has not been tested yet (I am printing it now), but will require custom supports, and some serious nerve as this is horrifying….  Enjoy!