print cases 3d models
1319484 3d models found related to print cases.thingiverse
WLANThermo Mini V3 Print-Case (86 x 86 x 32 MM) 10x M2x4 mm screws are required to secure the boards 4x M3x25 mm screws are required to screw to case 2x 40x5x2 mm magnets can be glued into the bottom Corner elements are required 4x. Side panels...
grabcad
This is a 3D Printed Case for the BotBlox GigaBlox board.Kindly designed and contributed by Martin Pecka and his team at the Czech Technical University.
thingiverse
This is a 3D print file of the case for Gherkin. To secure the case, use M2 screws (thickness = 2mm x length = 6mm) and insert nuts (M2 length: 3mm). ... If you connect the USB cable to the right side, flip the bottom plate as a mirror image and print.
thingiverse
... probably only work with flexible materials because it will be to stiff after printing. Version 3 should have the following print Settings: -0 Bottom or Top layers --> Then the Top and Bottom will be open, which lowers the stiffness of the part.
thingiverse
3D Printed Case for STM8. ...3D打印的STM8&STM8S开发板外壳。 You will need 4 x M3*10mm screws 你需要准备4枚 M3*10mm 的螺丝 Print Settings Rafts: No Supports: No Infill: 15% Post-Printing
thingiverse
0.5 = Nos. ...USBASP ISP 3d printed case. model 2. ...Print Settings Printer: magtech Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.25 Infill: 25% Notes: 0.5 = Nos Custom Section
thingiverse
This is a 3d printed case, ends and buttons for the Wise Clock, a great little arduino programmable clock that you can buy from the link below. Wise time with Arduino Instructions Printed at .254 layer height, 30% fill. Make sure your printer is...
grabcad
A simple 3d printed case for the 3Dconnexion SpaceMouse Wireless and its USB dongle.Warning: This mouse is very heavy, and the friction between the top and bottom is not enought to keep it closed in some situations, for example, holding it only from...
thingiverse
For the Udoo Antennas, use only the gold hex nut on the exterior of the 3D printed case (the lock nut washer takes too much thickness). I also had to hot glue the WIFI leads to the PCB to prevent them from detaching while assembling the antennas. ...
thingiverse
Customized version of https://www.thingiverse.com/thing:1230740 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1230740
thingiverse
Customized version of http://www.thingiverse.com/thing:74322 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=74322 Instructions Using the following options:...
grabcad
This is a test for a modular system that I will use to make a printed/laser cut acrylic PC case.
grabcad
3D printed model case for Xbee + Arduino nano.Enjoy!
thingiverse
3D Printed Case for XIAO-ESP32S3-Sense with heat sink ( 10 x 14 x 8 mm ), picture for details : case_top_b.stl and case_bottom_b.stl without heat sink : case_top.stl and case_bottom.stl
cults3d
When you do your Arduino DIY projects, it is good to have a case for them. ... This is easy to print case for Arduino UNO or Leonardo. ... It is designed to print without support, there are no brigdes as well.
thingiverse
This is a 3D print file of the case for Let ‘s Split. ... To secure the case, use M2 screws (thickness = 2mm x length = 6mm) and insert nuts (M2 length: 3mm).
thingiverse
... case-rap. It probably can be modified to fit other types of printer easily. By the way I very love my mks tft28, it "pimps" my case-rap 5 model. Print Settings Printer: Case-rap 5.0 Rafts: No Supports: No Resolution: 0,2 mm layer height Infill: 40%
pinshape
... case-rap. It probably can be modified to fit other types of printer easily. By the way I very love my mks tft28, it "pimps" my case-rap 5 model. Print Settings Printer: Case-rap 5.0 Rafts: No Supports: No Resolution: 0,2 mm layer height Infill: 40%
thingiverse
This is a remix for the printed case of the Tantillus, the Z middle part gets stuck on some screws on the backside otherwise. I used my old min endstop as max endstop and it works perfectly and will give you a little extra Z height.
thingiverse
I really liked this Let's split case but noticed an issue with the MCU port alignments being too high on the bottom. I have remixed the case to move the ports down in order to make room for the new Elite C v4 which is mid mount and requires lower...
grabcad
Access to the edge screen and home button are not restricted by this case.Also a port for the camera, heartbeat sensor, and flash, are present.There is no port for the loudspeaker*Dimensions 3.428 x 6.148 x .45 (Inches)87.0712 x 156.1592 x 11.43...
thingiverse
Hey guys, inspired by the classic virtual pet handheld device, I made this 3D print-able RePhone enclosure:) As an designer my purpose is to have as many Rephone owner as possible using this enclosure I've made. ...so youre so feel free to download it...
thingiverse
... Add supports for top half 3D Model iframe width="640" height="480" src="https://sketchfab.com/models/45f82572cb3b44baac50120039da4faa/embed" frameborder="0" allowfullscreen="allowfullscreen" Edi-Expand Gen 1 3D Printed Case by Tektyte on Sketchfab