print rite 3d models
1200961 3d models found related to print rite.thingiverse
... 3D Printer from Hobbyking Holds the Z axis Test card and The three most common Allen keys. ...i will release the plans for the printer stand. Print Settings Printer: Print-Rite Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Infill: 20
thingiverse
... I used double sided tape to mount it to the front of the electronics box, so no extra holes are needed in the original case. Needed a slightly longer cable than what came with the controller. Print Settings Printer: Print Rite Rafts: No Supports: No
thingiverse
Hey guys Made a "plan" for my Print-Rite Stand. It's really helpful to eliminate vibrations and stiffen up the whole printer. Used 15mm plywood. A "step by step guide" is in the Pdf file. you can find the printed base mounts here...
prusaprinters
This is a simple 40mm fan mount I designed for the Hobbyking Print Rite 3D printer. There are a lot of different designs out there, but this is my take on it. To mount, I just used double sided tape to stick it to the front of the extruder carriage,...
thingiverse
This is a simple 40mm fan mount I designed for the Hobbyking Print Rite 3D printer. There are a lot of different designs out there, but this is my take on it. To mount, I just used double sided tape to stick it to the front of the extruder carriage,...
thingiverse
Print Settings Printer: Print-rite DIY Rafts: No Supports: No Resolution: ,2 Infill: 30% Notes: Needs 2 m3 x 10mm screws 1 50mm squirrel cage fan The fan is glued to this bracket with cyanoacrylate glue. ...I currently have this fan powered in parallel...
thingiverse
Purchased a Print-Rite printer on a Black Friday deal. Printer seems very nice for the cost, but felt that the wobble in the the z-axis rods was a bit much. Designed and printed these stabilizers that slip into the top rail and helps hold the z-rods....
thingiverse
... coulisse facilement, ou faire quelques passages (gentils) avec une mêche de 8mm. Les trous sont prévus pour un boulon M3 de 35mm. Print Settings Printer: Print-Rite DY Rafts: No Supports: No Resolution: 0.2mm Infill: Between 30 and 50 Post-Printing
thingiverse
Mount that fit the carriage for Print-Rite DIY by shawdreamer https://www.thingiverse.com/thing:1755550
thingiverse
This is a case for the HobbyKing Print-Rite DIY LCD Screen (https://hobbyking.com/en_us/print-rite-diy-3d-printer-lcd-panel-without-casing.html) It can be used for other LCD screens of the the same size, depending on where the board for the...
thingiverse
Print Settings Printer: Print Rite Rafts: No Supports: No Infill: 20% Post-Printing After printing clean out the two holes so that it fits into the clips. Slide in the hall effect sensor it will clip into place, and connect it to the main board...
thingiverse
... the couplers to flexible ones. Maybe you have to rescale it, depends on your material Print Settings Printer Brand: RepRap Printer: Print Rite Colido DIY Rafts: No Supports: No Resolution: 0,2 Infill: 20 How I Designed This Designed in Tinkercad
thingiverse
Print Settings Printer: Print-Rite DIY Rafts: No Supports: No Resolution: 0.2 Infill: Your choice (between 10 and 30%) Notes: Yes, it looks like a WC but it does the job and it's very easy to print :) Print it upside down (like in the STL) How I...
thingiverse
Replacement part for the Print-Rite DIY carriage. I took the model from shawdreamer (take care to thanks him too). I made some improvements to fit the original parts better. It's also compatible with this cooler :...
thingiverse
Y-axis lightened replacements Print Settings Printer: colido printrite diy ramps1.4 Resolution: 0.3 Infill: 30%
thingiverse
This mounts two 50x15mm blower fan on the 3D printer that cools the printed layers. ...Still a work in progress. Print Settings Rafts: Doesn't Matter Supports: No
thingiverse
Print Settings Printer: PrintRite DIY 3D Rafts: No Supports: No Resolution: 200 micron layers Infill: solid Notes: PLA. Cold bed. Blue tape. Print a 2mm brim to help detach them. Post-Printing Trim Brim Nuff said. ...How I Designed This Designed in...
thingiverse
... required, just buy the 4 quid "tyre gauge" bolt it in place without modification and with some 2mm bolts and presto your away..... simples Print Settings Printer: Colido Printrite diy 3d printer Rafts: No Supports: No Resolution: .3 Infill: 30%
thingiverse
The difference in print quality is tremendous. You will need at least two (or four) M4 screws 20mm height to sandwich the top part, fan and bottom part and then you snap the part on. I have moved the fan a little to the left, so it doesn't touch...
thingiverse
... and needed a way to screw down the printer without modifying it. ...plans for the printer standhttp://www.thingiverse.com/thing:1216052 Print Settings Printer: Print-Rite Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Infill: 30%
thingiverse
A simple thumbwheel to adjust bed level Designed for M3 self-locking nut. ...Print Settings Printer: Print Rite 3D Colido 3D Printer Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Infill: 30%
thingiverse
This is a removable tray to place on the base rails of the Print Rite DIY 3D printer. ...It catches random extrusions underneath the print head, keeping your desk or printer enclosure clean.
thingiverse
... short) 8x5mm washers 12x3mm screws with nuts to fix to bed This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/5C4dCAl0DoC Print Settings Printer: colido print rite Rafts: No Supports: No Resolution: 0.3 Infill: 30
myminifactory
Nice solid piece to hold an acrylic bed you can set level on the colido diy print-rite 6mm acrylic4x50mm M5 screws and wing nuts4 springs (cut short)8x5mm washers12x3mm screws with nuts to fix to bed This thing was made with Tinkercad. ...Edit it online...
thingiverse
Stop your Z Travel Shaking Print Settings Printer: Print Rite 3D Colido 3D Printer Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.4 Infill: 30% Notes: After i saw that the Extruder is forward and backward jerky if the Z Axis is moving i...
thingiverse
... with the plate is really plane. I printed them with support in the center, but you can try without. Infill as you wish, 20% is enough. Print Settings Printer: Print-Rite DIY Rafts: No Supports: Yes Resolution: 0.2mm Infill: Between 10% and 30%
thingiverse
... a longer 5mm screw to replace the original Idler screw and a 4mm screw for the 2 new bearings. Print Settings Printer: Print-rite DIY Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: Printed at 0.2mm Infill: 30% Notes: Piece of cake :)
thingiverse
Print Settings Printer: Print Rite 3D Printer Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Infill: 50 Notes: At the moment the parts are PLA. How I Designed This I get the part inspiration from this Blog:...
thingiverse
One is for the uploaded Print-rite Y-axis block model ONLY. https://www.thingiverse.com/thing:1654491 ( By: shawdreamer ) 2. The other baring cover is for the original factory Y-axis block. 3. I've also remixed the right block as the belt...
thingiverse
Made it a little more easy to assemble for the roller and added a captive nut for the z endstop.