print strip 3d models

Strip terminal hardware device used to communicate information between systems over a network

The strip is specifically designed to ensure smooth operation and easy installation for rolling shutter systems.

Clip to screw an LED light strip to the underside of a shelf or cabinet.

In 2012, the Mobius strip was creatively modeled via surface modeling techniques within SolidWorks software.

I created a bracket for the power strip. ...It is minimalist and needs little filament.

Sometimes LED strips refuse to adhere properly. ...To overcome this challenge, use two-sided adhesive tape.

A led strip holder, with corners and a case for wemos and power supply

This is a versatile LED strip holder featuring a sleek 45-degree angle design.

Designed to slip under the shingle and hold the led strip.

Flexible adaptors for linking LED light strips directly into extruded aluminium framing profiles.

To prevent the LED strip from falling, we need to secure it properly.

... frame clip for double-sided glue tape Printed with 0.4mm nozzle and 0.1 and 0.2mm layer height. You may need to cut through the middle when printing with heigher temperature or some other printing options that can cause merging the clip 'arms'.

This particular model prints exceptionally well on dual-filament printers, utilizing both model and support filament for optimal results. ...I am actively working to develop a new shelf design that is optimized for single-filament printers, offering...

A Scene from "Pickles" Comic Strip If You're Unfamiliar with Pickles, Check It Out Online The comic strip by Brian Crane is a favorite of my wife and me, and I highly recommend checking it out on the web. The characters are so well-developed that...

... etc. to mount to whatever you like. Designed to work on fully encased (IP-65 waterproof) strip, but will also work with IP-65 (splash-proof) strip. I have not tested with IP-30 (non-waterproof) strip. ... It should fit, but it might be too loose.

By embracing the right choice and selecting the appropriate type of LED strip according to their 3D printer model, users can maximize print accuracy while also making efficient use of energy resources by selecting lights with a sufficient power...

The default settings below are for a standard 5 Amp terminal strip (see above photo). Parameters: Num_of_terminals = 4; /// Default is 2. Range: [2-12] wire_outter_dia = 7.3; // Default is 7.3 block_width = 6.4; /// Default is 6.4 block_gap =...

The great thing about this project is that you can print out multiple copies of each part, making it easy to customize and expand as needed. My design includes a sturdy dovetail mounting strip, a slotted holder for small parts, and a handy bin for...

----------------------------------------ENGLISH------------------------------------- This is a support to place a power strip under the table without having to make any type of hole or glue it, it is simply hooked to the edge of the table (the width...

To navigate this compact area during nighttime activities, I've installed bright white LED strips along with red ones specifically designed for eyes adjusted to darkness - they're an incredible asset. However, when trying to adhere these strip...

Human: I built a DIY WiFi power strip using a 3D printed case, a Sonoff WiFi switch, old outlets & some old extension cords. The total cost for each strip was under $10. Control the unit with Sonoff's mobile app, Alexa, or the onboard switch. You...

Fidget strip to drive your wife or collegues to despair.It's an easy print and can be assembled easily (maybe some pliers to help the arms of the top get into place).04-07-2022: Updated the design with a new bottom-top snap-fit that is even easier to...

Three versions are available: normal, double-sided one side, second side flat to avoid hitting the extruder while working (on certain printers) and one without a frame clip for double-sided glue tape attachment Printed with a 0.4mm nozzle and layer...

This test strip allows evaluation of various filament diameters which are 0.4, 0.5, 0.6, 0.7, 0.8, 0.9, 1.0, 1.2, 1.4, 1.6, 1.8, and 2.0mm. However, the 0.4mm thickness didn't appear in ReplicatorG or print out. For printing, use 100% infill and 4...

My led strip was falling down due to its own weight so I designed this simple holders to leave it in place on the IKEA KALLAX shelf (37mm external boards). Print it as you like, it can be done with 2 outer layers and 0.3mm layer height as there is...

 The diffuser should be printed in white to reduce the harshness of the direct LEDs. Both parts should be printed at 0.2mm layer height, with a 0.4mm nozzle. ... This will result in 2 layers of white filament for the diffuser panel and a...

To connect several led strip holder from rezkom https://www.thingiverse.com/thing:3667332 Print Settings Printer: Prusa Mini Rafts: NoSupports: No Resolution: .2 Filament: SUNLU PETG Notes: print on the side Category: Decor

Due to lack of overhangs, you might not require the printed part for the final object; instead, glue the dowels together within the slots. If it seems insufficiently striplike, opt for a thinner backbone; initially, I found the first version too...

Welcome to my first thing on Thingiverse, today I'm 1 month into 3D printing and already sharing one of my first projects where I used my iPad to create something on my own –hope you'll enjoy it. Basically, I designed a LED stand that stores a...

It can indeed be printed directly on the Ender 3 when oriented at an angle, requiring diagonal alignment. For optimal results, consider printing it with supports in place to secure the LED channel. A second design option features slots accommodating...