print tube 3d models
1240883 3d models found related to print tube.thingiverse
Simple, quick to print tube squeezer. ...Inner length is 52mm which should fit most standard tubes.
cults3d
-no need support -Print speed can be increased due to the design of curved cornerseasy print Wide application: the tube squeezer works well for tubes of width less than 55mm, works on aluminum and plastic tubes, suitable for squeeze toothpaste, cream...
thingiverse
This is a spacer for the printed tube for the Ikea Samla filament storage solution. The tube can be found at the URL below. Three of these are used. One spacer goes between each roll of filament. The spacers are 10mm wide, 15mm in height and the ID...
grabcad
... of marking tubes 1.125 and smaller. 3D Printed Tube Center Finder:2x-(0.25x0.50) Dowel Pins (McMastercarr)1x-Framing Nail1x-M3 Threaded insert (McMastercarr)1x-M3 Bolt 10mm (McMastercarr)The part is printed in ABS with the dowel pins pressed in.
thingiverse
The tube holder is very reliable and rigid, unlike the others that are presented here. I recommend this part for manufacturing to all owners of this printer. ... I has make it from SBS plastic with 25% infill, 80mm/s, layer 0,2mm, head 250C, bed 80C,...
thingiverse
... designed these. ...If you are printing my mag follower as well you need a well tuned printer for reliable shell feeding. This will most likely make the priming louder and rougher from print on print sliding. ... Mini Versions will be added shortly.
youmagine
One of the simplest ways to attach soft tubing to other soft tubing is with the use of barbed adapters. They can be used to connect different diameters or the same diameters. Unfortunately, some sizes, like 1/16" to 1/8" are not sold (or are at least...
thingiverse
One of my students printed this awesome looking speaker! ...Works great, also compatible with iPhone 5.
cults3d
One of my students printed this awesome looking speaker! ...Works great, also compatible with iPhone 5.
thingiverse
I made this tube holder to work with the d-bot print carriage for the Titan Aero, which is found at the following link: https://www.thingiverse.com/thing:2253498 This was done so I had a holder for my ptfe tube, and my wiring. ...I wanted it beefed up a...
thingiverse
3d print based simple vacuum tube transmitter. Transmits on the 80m band (3.5-3.8Mhz). Also works on 40m with either less turns on the tank, or less capacitance. Designed to work with many dual octal triodes. Use schematic as reference and make...
thingiverse
Teflon tube stuck in your fitting that is really only designed for pneumatic tubing? Building a 3d printer on the cheap? CANNOT wait for that one part to come in? Then fear not! .... all you need is a tap wrench set or even just a nut and with this...
thingiverse
Tested, next update will make the tube hollow for faster printing and better filament efficiency. 21 Dec 2016: New Version 3! More gaps to accommodate printer inaccuracies and structural alterations to make it print better. Works well, but might need...
thingiverse
The tube must spin quite fast to keep the right direction. I don't know if it was on the original toy but I've added a wing profile on the top. Priting size 50%. Priting time: 1h30 Plastic weight: around 10g Have fun ! ... ...
thingiverse
Here's a great solution for the post-processing of 3d printed pipes and tubes... or any other pipe or tube hanging around that you want to apply a professional looking spray paint finish to. Check out the video for full details.
cults3d
A small wall mounted tube holder for filament guide. ...Put it on the wall with some double sided tape.
prusaprinters
Fits well into Capricorn (and others) 2/4mm PTFE tubes without adaptors. fs-cover requires support. Recommend to use PETG (black for the fs-cover) and quality settings. ...Be ware of “elephant foot”</p><p>Rollers inside the drybox are designed for...
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=49604 Instructions Using the following options: number_of_tubes = 1 number_of_coins = 10 fudge_factor = 0.975 clearance = 0.4 generate_cap = 1 coin_type = 13 tube_wall = 2 generate_tube = 1
thingiverse
Cool single print of integrated extendable tubes. Base print is 60 mm tall. Extends to 560 mm. (Make sure part is oriented in printer utility such that rings are touching the base) Instructions...
prusaprinters
(Like pancake:) Please watch added video.Then take Mount tool, put in the cables and push over Cable Flexible Spiral TubeThe Tube is 21cm long, but you can add them endlessly, cut them, one over next one…After mount on cable, you can lock ROLO itself...
thingiverse
A simple design for upright holding the test tube of standard COVID-19 tests. Especially bulk packages are often only supplied with one holder. ...Great for team testing.
grabcad
The Top / Bottom / Middle support can be printed without supports. Assemble using 1" PVC at whatever length is best for your arrows. You will need to make a belt attachment using either nylon webbing or paracord, multiple loops are available on the...
myminifactory
Here is a print-in-place moveable tube that can be added on to any design. The reasion for using this object is to allow for tubes to be printed anywhere in a print that will not need support for (a revolving object or a extention bar) and it...
grabcad
but but but but on the ultimaker², for 72 tubes, it takes less than a day to print 15 rails and 16 assemblers for different printers, do just 1 rail and 2 assembler to see if they fit and doesn't have too much play (you have to be able to put 2...
thingiverse
These are some coin tubes that work perfectly with Australian coins. ...Currently there are only ones that are 60mm tall but there are some taller ones to come soon.
thingiverse
This is the base of a 3D printed NMR tube cleaner which allows up to 5 tubes to be cleaned at once. It is recommended to print with the polypropylene (PP) for better resistance to organic solvents. PP packing tape was used on the printing bed to help...
prusaprinters
Drill LACK enclosure with 3/8" or 10mm drill bit for the guide tube. Print instructionsA PETG tube ferrule for feeding filament through a 4mm PTFE tube from a dehydrator to your printer enclosure to keep dry. Print vertical. No supports.<br/> Cleanup...