printed thumb drives 3d models
1237268 3d models found related to printed thumb drives.grabcad
Here is a little thing i done just for fun and later for 3d print, a USB thumb drive and card holder, i can hold 8 thumb drive, 6 Micro SD Cards and 4 Normal sized Cards. ... Hope you like!
thingiverse
Oh Hi, Hello The thumb pick it is ;P Made this just out of curiosity, and it came out pretty impressive- actualy more comfortable than oryginal - dunlop- it was modeled to be the closest to it as I could unfortunatly I modeled it in bad scale and had...
prusaprinters
This is a fully printed Thumb Screw and nut suitable for low strain, low stress applications. I had a need for a threaded thumb screw and nut, but hand no metal parts on hand, so merged SubSite's Tripod Screw Nut with Nikolica's m5...
grabcad
... to. I salvaged the bearing from a Hard Drive reader arm (Great Movement), the screws as well. I uploaded the model, shelled ready to print. Although, one side still needs supports. ...But it turned out pretty cool, and the tolerances were dead on.
thingiverse
Needed to mount a Seagate 8TB drive to a wall and keep it cool. Recommend 3 mm screws (10mm or 12 mm long). I ended up using #6-32 3/4 inch because I had them handy. Letters A,B,C,D help match parts for assembly. (letters go on the inside of...
thingiverse
Instructions Print this with the round end facing down! Printed in PLA, 100% infill with support @ .1mm layer height -Lightly sand the outside of the lower open round portion with 800 then 1000 grit sandpaper. -If you want the top smooth, sand...
thingiverse
Based on this thing by me5647, "USB thing holder with center hole for magnet", https://www.thingiverse.com/thing:847379 I wanted all of the slots to be angled up and straight. I only screwed in the top left and bottom right and it seems pretty...
cults3d
Based on this thing by me5647, "USB thing holder with center hole for magnet", https://www.thingiverse.com/thing:847379 I wanted all of the slots to be angled up and straight. I only screwed in the top left and bottom right and it seems pretty...
thingiverse
3D printed Louis Vuitton x Gucci USB Thumb Drive Fits Lexar USB 2.0 #Dabonhaters #HypeBeast #Itseverydaybro
prusaprinters
Holding up to 6 USB thumb drives in a convenient way.Easy to print, not support needed. USB-Stick-Halter mit Platz für 6!Einfach zu Drucken, keine Stützstruktur nötig.
thingiverse
There are lots of cool USB thumb drive holders here, but I wanted to roll my own.
thingiverse
... thumb drives. ...It's easy to forget which thumb drive is used for what purpose. This handy tool helps me keep things in order. At a school site, someone may think the thumb drive belongs to them. Nope! Not this one. ...This one is for the 3D printer.
cults3d
... thumb drives. ...It's easy to forget which thumb drive is used for what purpose. This handy tool helps me keep things in order. At a school site, someone may think the thumb drive belongs to them. Nope! Not this one. ...This one is for the 3D printer.
thingiverse
I made the SD Card holder from n2b8 and then decided I wanted a place for all my thumb drives as well. So I designed this. ...
thingiverse
... bugs were fixed and new files uploaded -- Mod for the 2.4 GHz Mini Remote to be used in thumb driven configuration. ... More information and instructions on ESK8 builders forum: https://www.electric-skateboard.builders/t/mini-remote-thumb-drive/74306
thingiverse
Take apart a Lexar USB flash drive and remove the circuit board This model will fit LEXAR Thumb drives 2.0 and 3.0 the Nintendo controller houses the Data stick Pro usb size I added a USB extension to be able to extend the USB port connector. Add...
thingiverse
... I've printed this standing up on its end (green) or on the side (like the STL, the red print); I prefer on its side even though you need some supports for greater strength along the length of the piece to resist small hands snapping it in half.
thingiverse
I designed this enclosure to allow for a small magnet to be installed inside the enclosure to attach the drive to the side of a computer case or other metal shelves. ... I will add photos of the assembly later and edit this to reflect the steps used.
cults3d
Print the case up to 75% of its height, pause the print, insert the electronic module and continue the print as in the shown pictures. ... Recommended print settings: -0.3mm layer height, -3 shells -3 top layers -3 bottom layers -15% infill
thingiverse
Print the case up to 75% of its height, pause the print, insert the electronic module and continue the print as in the shown pictures. ... Recommended print settings: -0.3mm layer height, -3 shells -3 top layers -3 bottom layers -15% infill
thingiverse
... before. ... I have printed many of these of the people in our office. there are 2 version of it the second version has slots for SD and Micro SD cards. I may or may not put that one up on this site. ... you can find it on Grab Cad and other sites.
thingiverse
... allows the clip to be secured with a nut or similar fastener. Male-female notches hold the clip and hub assembly together allowing it to be removed and replaced as necessary. **Rotate both components bottom side down to print without supports.**