printer cord adapter 3d models

End caps for a lenovo power adapter with cord wraps Print instructionsPrinted in Amazon basics PLA with support at 82.5 degree overhangs at 65mm/s

A bracket to provide strain-relief for a 9mm grounded power cable running to the bed heater on a Kossel Delta. ...Uses two M3 screws to anchor to the 2020 extrusions at the base of the printer and two 3mm zip ties to grab the power cord.

Simple adapter for ink printers eeprom

... I also use it to clip the wall cord, which i have switched the 3 foot cord that comes with the XPS for a 1 foot cord. Print Settings Printer Brand: Prusa Printer: Prusa Mk2 Rafts: No Supports: No Resolution: .2 Infill: 20% Category: Electronics

update; there are two stl files one original and one for the narrow version for 2017 adapters I made this clip to attach to my dell xps power adapter to keep the cords neat in my laptop bag. With this clip i can pull out as much or as little cord...

Modified PRUSA adapter-printer-mmu2s part. This part guides the filament from the PTFE tube to the gears in the extruder. IMHO the inlet of the part is too small/steep (see image right). This causes filament to stuck before the gears. This behavior...

Attached Spool Holder for Dremel 3D printers.

Short manual how to do it: remove print bed Remove wheels from the carriage use these screws to mount the adapters, loose the x-profiles for y motion and put the spacers below it screw your linear rails to the profiles, mount the adapter(s) to your...

This is a box to put around a Dell LA65NS2-01 65W 19.5V 3.34A laptop AC power adapter / laptop charger. It gives it tabs so you can wrap the cord/cable around it. My power adapter came with a velcro strap. It comes in two halves. you can glue them...

Spool adapters are drawn in Onshape. The sizes I made are exported as STEP and uploaded here. ID is 31mm on all (sized for Qidi Max). OD is 55, 56, and 74mm.If you have Onshape, the link below will open a public document and you can modify the ID,...

Things to come: rounded corners better "snap" Extension cord clip (so you don't have to overlap or tie a knot after winding) Update1: spoolMountWithPlugHolder6.stl has a little better "snap"Update2: spoolMountWithPlugHolder8.stl has rounded, flush...

The [Rollease Acmeda ARC Automate cord-lift motors](https://www.rolleaseacmeda.com/docs/default-source/default-document-library/cl-motor_prgm_gl_v29f0d8d91b1e86477b58fff00006709da.pdf?sfvrsn=d1e5e93c_0) -- used, for example, with Roman blinds -- are...

Repurpose the cigarette lighter opening in your car to hold a USB extension cord attached to a new car stereo

I got sick of tangled cords and the power adapter kept getting caught on everything while trying to pull it from the bag. This cable wrap is for the Dell Slim Power Adapter 65w and 90w models. The adapters came with Dell Latitudes in the past couple...

Battery adapter for FP40 thermal printer

Plotter adapter for 3D printer. ... Diameters: -3,5 mm; -7,5 mm.

Adapter to attach an all metal E3Dv6 hotend to the Overlord 3D printer. ... See instructions tab for more details.

... and utilize a 100 mm Pipefan for effective ventilation. ...The adapter allows you to connect a ventilation system to your 3D Resin printer, and paint booth helping to dissipate heat and toxic fumes and improve air circulation around the printing area.

I had a slight problem with the power adapter of my hotbed, so I had to print a replacement to use until the actual part arrived.  This is for an ANet 3d printer hotbed power and thermistor.

Universal 3D Printer Spool Adapter ================================== This universal design adapts a filament supplier's spool to a 3d printer's spool holder. Initially I created two entries adapting HobbyKing and Mamorubot spools to a Cocoon Create...

It is desirable to have this "Adapter-Printer" easily removable because its location in the filament feed path is subject to accumulation of dust and lint, which can negatively affect performance of the filament sensor. ... My redesign makes the part...

design and build a CNC adapter for the REP RAP Wallce ++ (M8 Edition) 2 - M4 bolts 50mm long 4 - M4 washers 2 - M4 nuts The motor used for the CNC was out of an older HP printer T the motor model number is as follows C4531-60012 (24 volt I think? :/)...

I bought a Rollo label printer and it's awesome. The only problem I had with it, was that it does not "support" printing labels with a paper width less than 4cm (1.57″). I solved this problem by printing some arm extension clamps so that it can guide...

This is a chip holder that allows CubeX owners to free up some internal room inside the printer. This is useful if you are using bulk filament cartridges. Instructions Print "butt" side down, the...

The Wanhao printer, is using guides (tubes), to guide the filament from the spool to the extruder. This is so the filament wont break. But the guides don't actually fit in the holes inside the extruder. This "thing" is a small adaptor part, that...

... unraveling the entire cord `[3b]`. The STL files are intended for well-optimized printers with tight tolerances. Fusion360 files are also included so you can customize the design for your printer and for other power adapters and power cords.

Fit a Ugreen USB-C extension cord into a USB-A extension cord spot like a backpack charger passthrough Also available [on PrusaPrinters](https://www.prusaprinters.org/prints/73466-usb-c-extension-cord-to-usb-a-backpack-adapter)

... garage. ... But the hardware store only had Nema 6-20 cord end plugs. So I bought the plug and made this outlet face plate adapter. So now I can install this as an outlet in my garage. Cheers. ... PS: This is for an American standard 1 gang box.

So I bought the plug and made this outlet face plate adapter. So now I can install this as an outlet in my garage. ...Cheers.</p> <p>PS: This is for an American standard 1 gang box.</p> <h3>Print instructions</h3><p>Unassociated tags: Nema 6-20<br/>...

Insert the positive pole of the battery into the 1.6mm power cord use nail clippers to cut off the excess power cord