printer height 3d models
600124 3d models found related to printer height.
thingiverse
Adjustable 3d Printer Height Adjustment Wheel for M4 Nut
thingiverse
I experienced excessive heat under the printer during a long time print job. To avoid overheating and it's effects (accidental safety stop, demage, etc.) I designed these leg extensions to fit into the existing legs. ...I made a place for a D10mm...
thingiverse
Reduced height by 3mm
thingiverse
Legs for the printer regulated on height. For exposure of the printer on level, or on not a plain surface. I used the plastic PLA, filling of 25 - 35%, under the basis it is possible to enclose rubber/silicone. For assembly were used: The M4x35...
thingiverse
This makes it hard to print using a 0.05mm layer thickness in this location because the change in bed height is almost a full 0.05mm layer thickness. The first two pics are with a 0.05 layer The last pic is a 0.1mm layer with a slightly increased...
thingiverse
Customized version of http://www.thingiverse.com/thing:43783 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=43783 Instructions Using the following options: height = 3.4
thingiverse
Insert spring + secondary nut Screw into position on printer (hanging, flat side facing towards printer plate) Thread rod in from the top. This is part of my Ender 3 single stepper dual Z system. Find all parts here: ...
thingiverse
Customized version of https://www.thingiverse.com/thing:3232756 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3232756
thingiverse
I build this as some of my spools were too large for the stock arm, this gives at least an extra 50mm clearance.
pinshape
Move the Monoprice Z-Axis limit switch mount to the outside of the frame, using the original screws coming from the inside of the printer frame. Mount the limit switch to the Sensor L-Bracket using two 1.91 x 10mm plastite screws which in turn...
thingiverse
Firstly i made the mount plate thicker, the original broke coming off the printer, 2nd i made the ball tension-er item flower-thing more rigid to hold the ball alot more firmly, as in that ball isnt coming out even if you lift or move the printer. i...
thingiverse
There have been some recent changes to the Mendel printer frame and my printer is about 8 months old, so make sure you have a close look at your printer to make sure that this modification will work. Looking at the new model I don't think my update...
thingiverse
I would like to share a new guide for the max to change the position of the filament to front of the printer .it also guides the filament when going to max height .
thingiverse
Adjusting the nozzle height on some dual nozzle printer rely solely on the accuracy of the components. One such printer is the German RepRap X400. There is no easy way of setting both nozzle's height correctly. This nozzle seat solves this problem...
prusaprinters
Tightening screw for the nozzle added to fully secure it in place. UPDATE 2: Use the vernier patterns to calculate the nozzle offsets down to 0.1mm. Print instructionsUnassociated tags: adjustable height, fan duct, tightening screw Category: 3D...
cults3d
So recently I decided to make a riser for the bed-height sensor switch so I could reinstall the glass plate and stick the flex plate onto it. That's worked out really well as I can set the z-offset easily and the flex plate is much more level. It's...
thingiverse
So recently I decided to make a riser for the bed-height sensor switch so I could reinstall the glass plate and stick the flex plate onto it. That's worked out really well as I can set the z-offset easily and the flex plate is much more level. It's...
thingiverse
However, after modifying my printer, the height was still limited. In my case, the spool was rubbing against the canvas, risking to hinder its rotation… So I made a top bar in order to stretch the canvas and gain another 1cm, which allows me...