printer hub 3d models
348071 3d models found related to printer hub.cults3d
3d printer bushing support 3d printer hub support for 3D printer zonestar or Anet-A8 linear bearing support 3D printer printer linear bearing support
thingiverse
Zerbra Printer GK420d Thermal Label Printer Hub Adapter I made this simple part to reduce slop. ... corwellcustoms
myminifactory
Here's yet another design for a 3D Printer Spool Hub / Holder. This design uses a piece of 8 mm threaded rod, two 0608 bearings, a couple of 8 mm nuts, and two more 8 mm nuts or in my case two 8 mm acorn nuts for a more polished look. The two 8 mm...
thingiverse
Here's yet another design for a 3D Printer Spool Hub / Holder. This design uses a piece of 8 mm threaded rod, two 0608 bearings, a couple of 8 mm nuts, and two more 8 mm nuts or in my case two 8 mm acorn nuts for a more polished look. The two 8 mm...
thingiverse
The hub is turning directly on the M8 threaded rod. Concerned about wear. Both types A and B conform to the following spools. ... Polymakr Black Spool 55.2mm ( 54.4mm ) eSUN Black Spool 53.5mm ( 52.8mm ) eSUN...
grabcad
Adjustable using the standard skate board bearings industrial standard "608" size, with a bore of 8 mm, an outer diameter of 22 mm, and a width of 7 mm.
thingiverse
Hubs for 3D printer filament. One hub is 52mm ,the other is 72mm and they both fit a 10mm shaft. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/lb6kx6xTd4S
thingiverse
The paper roll hub made to fit a HP T610 44in wide format printer. No flexible parts to keep breaking. Works great for most brands of 2" core paper rolls. FYI This is the dummy end, not the drive end. Print Settings Printer Brand: RepRap Printer:...
prusaprinters
I also Uploaded the .stp for the slider button so you can adjust the design, if you find they wont fit properly. Print instructionsCategory: 3D Printer Accessories Print Settings Printer: CTC 3D Rafts: Doesn't Matter Supports: Doesn't Matter...
thingiverse
... V2 (tighter tolerances). I also Uploaded the .stp for the slider button so you can adjust the design, if you find they wont fit properly. Print Settings Printer: CTC 3D Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Infill: 15%
myminifactory
It should fit many different printers, but I designed it for my Replicator-Clone. The Fan controller I used was the Aerocool F5XT:http://www.aerocool.com.tw/en/fan-controller/single-bay/f5xt The circuit board can be loosened very easy and the...
cults3d
It should fit many different printers, but I designed it for my Replicator-Clone. The Fan controller I used was the Aerocool F5XT:http://www.aerocool.com.tw/en/fan-controller/single-bay/f5xt The circuit board can be loosened very easy and the...
pinshape
It should fit many different printers, but I designed it for my Replicator-Clone. The Fan controller I used was the Aerocool F5XT: http://www.aerocool.com.tw/en/fan-controller/single-bay/f5xt The circuit board can be loosened very easy and the...
thingiverse
hub connector to power a series of fans that allows me to extract hot air from my box to keep a constant temperature.
thingiverse
This is a hub intended to position electrical contacts onto the microchip on certain 3D printing cartridges. There are two versions now. ...Hub2 is smaller and much faster to print.
thingiverse
...For a smaller filament spool hub click the link below for a 38mm spool hub.http://www.thingiverse.com/thing:1710599 Print Settings Printer: Alunar Prsua i3 Rafts: Yes Supports: Yes Resolution: 0.1 Infill: 100% Notes: Printed vertical on printer bed.
thingiverse
In short, though, this hub mount is printable on a small printer (the MPMD has a print surface of 110mm in diameter) and snaps together without any extra hardware or glue. I used Cura as my slicer and enabled tree supports to support the top of...
thingiverse
This is a hub for the filament spooler holder of the Eryone ER-20 that includes two ball bearings 10x30x9mm. The 10mm ID of the bearings fit perfectly on the spooler holder. The Cura based gcode will stop at the right height in order to insert the...
myminifactory
Load "1-base-black" file & start print. (black material) After finish, don't remove the model from platform, then change orange material. Load "2-orange" file with "tower" file & start print. ("Tower" file must be behind 10 mm from the model) ...
grabcad
Designed to fit the spool holder of a stock CR-10, but it will work with other printers, too. The springy part is tapered so it fits tightly in a variety of spools. Tested it and it works well on Inland, Hatchbox, and other brands. Should be scalable...