printer o 3d models

Theoretical XY Positioning resolution of 0.02mm (20 microns or 0.0008") Theoretical XY Maximum Feedrate of up to 5000mm/minute (roughly 200 IPM) Theoretical Z Positioning resolution of 0.005mm (5 microns / or 0.0002") Theoretical Z Positioning...

Hence, here is a Work-in-Progress Thing-o-Matic 3D Printer Manual. At the moment it is more of a 1st time User or Quickstart Guide but it will shortly be augmented with detailed instructions on how to repair, maintain, troubleshoot and design for...

This is an enclosure for the Ender 3 v2 but can be resized for any printer. This is made from 5mm mdf. I superglued it together and reinforced with 1 x 1 strips of wood. Any type of construction will do the job, I just didn't have a working pin...

Hence, here is another section of my Work-in-Progress Thing-o-Matic 3D Printer Manual, dealing with Post-Processing of Printed Items such as the following: Removing Parts – Taking the object from the printer and separating individual parts or...

so I made a scratch built printer from wood, nylon sheets, L shaped angle aluminum, wire ties and hot glue and it works really well but it could be better, you can see those exploits here http://rob-o-printer.blogspot.com/ I bought new printer parts...

... file. ...open thing file and print 10% fill Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator Rafts: Doesn't Matter Supports: Doesn't Matter Notes: I printed on my replicator Dual. ...Use dual print standard settings will be fine/

Spool holder mounts on your desk or above a 3D printer. ... Holds wide spools.

Spool holder mounts on your desk or above a 3D printer. ... Holds wide spools.

This is just a quick design I made for the rear I/O of the printer. It replaces one of the bottom corner brackets and can fit a power connector, USB pass, ON/OFF switch (17.5x12mm cutout) and a fuse holder (panel mount fuse holder for 20x5 mm fuses,...

This is just a quick design I made for the rear I/O of the printer. It replaces one of the bottom corner brackets and can fit a power connector, USB pass, ON/OFF switch (17.5x12mm cutout) and a fuse holder (panel mount fuse holder for 20x5 mm fuses,...

This is just a quick design I made for the rear I/O of the printer. ...It replaces one of the bottom corner brackets and can fit a power connector, USB pass, ON/OFF switch (17.5x12mm cutout) and a fuse holder (panel mount fuse holder for 20x5 mm fuses,...

The frame is the only part of the Sphere-O-Bot that requires a large printer. @jjrobotics if you happen to see this, nicer tabs, a few well placed holes and some screws in the kit would be a great permanent fix for customers with small printers. ...

A remix of this https://www.thingiverse.com/thing:2039168 design just to make it fit my MK3 heat bed.

Cut the Sphere-O-Bot main frame in half as it was too large for my printer bed (Lulzbot Mini) This should now fit on most printer beds.

Cut the Sphere-O-Bot main frame in half as it was too large for my printer bed (Lulzbot Mini) This should now fit on most printer beds. Post-Printing Steps 1.) Print out the two pieces. 2.) Using sandpaper, finely sand down the two...

O

o

o

O Grille

OTCR letter O

Customized version of http://www.thingiverse.com/thing:356902 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=356902 Instructions Using the following options: Message = O

Customized version of http://www.thingiverse.com/thing:46862 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=46862 Instructions Using the following options: _1_piece = O _3_depth = 60 _4_thickness = 4 _2_size = 30

Customized version of http://www.thingiverse.com/thing:46862 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=46862 Instructions Using the following options: _4_thickness = 2 _3_depth = 10 _2_size = 10 _1_piece = O

The "O" concept offer a little more height and this mean a little more comfort in use and aesthetically an interesting towel hovering sensation over the "O" ring base. This way the base is not visually obstructive and give the "air" sensation in the...

Customized version of http://www.thingiverse.com/thing:46862 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=46862 Instructions Using the following options: _4_thickness = 2 _3_depth = 60 _2_size = 60 _1_piece = O

http://www.thingiverse.com/apps/customizer/run?thing_id=1148986 Instructions Using the following options: twist = -5 letter_5_height = 4 letter_1_height = 6 Text = O Font_name = Chewy Loop_font = Chewy letter_4_height = 6 letter_4_space = 10...

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=434613 Instructions Using the following options: gravitovectometer_ball_diameter = 7 gravitovectometer = 0 rings = 4 height = 5 s = 1.04 d = 3.5 letter = o

http://www.thingiverse.com/apps/customizer/run?thing_id=714444 Instructions Using the following options: font_catch_diacritical_sign = 2.3 RoundedBase = 0 baseheight_percent = .33 fontname = Orbitron textstring = O textsize = 16...

http://www.thingiverse.com/apps/customizer/run?thing_id=114247 Instructions Using the following options: pin_cap_width = 4 ring_height = 6 center_radius = 12 pin_radius = 2.45 Build_Plate_Manual_Length = 100 pin_hole_radius = 3 pin_cap_gap = .45...