printing with tpu 3d models

This marshmallow stress toy is designed to be printed using TPU filament.

These friction Boots for the corner feet work great to dampen the printer noise, and prevent it from "dancing over the table" Be sure to read print settings to use TPU. ... IF you print in PLA or ABS, you will need to attached some other rubber cushion...

this is Friction rubber ball for YakFisher 1.5" Ball Systemprint with TPU filament or any flexible material with 100% infill

Hi there I used my own model of the weight part to make a Voronoi of it using online voronoi tool: https://www.voronator.com to be printed in tpu flexible (53D). it worked just good. the problem was the former version was too hard and may be a...

Printed by Stratasts F370.The inside structure was made by controlled sparse fill.

I tried repairing it with TPU printing. I made it with TPU filament I had on hand, but there are softer filaments, so please try them. No problem in listening test.　　（my thoughts） Although we cannot perform characteristic tests and endurance...

This project uses low temps, high extractions, slow speeds, and several other tweaks to remove oozing and major defects with this specific TPU filament.  Make sure to have your tensioner screw as loose as possible and use a 0.4mm nozzle.

I tried repairing it with TPU printing. I made it with TPU filament I had on hand, but there are softer filaments available, so please try them out. The edges are designed to be attached without glue. Of course, gluing is also acceptable. There...

I tried repairing it with TPU printing. I made it with TPU filament I had on hand, but there are softer filaments, so please try them. The edges are designed without gluing. Of course, it is OK to glue. No problem in listening test.　　（my...

This is my work in progress "mouse bungee" using a 608zz skateboard bearing and flexible filament for the cable arm. What is a mouse bungee? First of all it should prevent your mouse cable from getting caught up on stuff from your desk. This will...

The case has a built in hinge and a simple locking mechanism. ⭐Filament acquired from Aliexpress (affiliate links): PLA: https://s.click.aliexpress.com/e/_A8tY4x TPU: https://s.click.aliexpress.com/e/_A34m47  ⭐Mellow Direct...

I wanted to see if it would be possible to create a cool looking nexus 5 case out of TPU filament. It's currently in the printer. ... I used Meshmixer to create the hole pattern.

This mask can be used against coronavirus, it can also be modified as you want Tha mask's base is printed 0.3mm Once you print it You can proceed by printing the second layer 0.2 mm The initial layer line width is 120% The mask is glued with a...

... to get even better adhesion to a Glass Bed. Print without Raft or Brim, with your preferred TPU settings. I made one remix with 2 adhesion flaps, and one with 4 (giving even more grip) Freecad file is included if you like to change things. ...

Printed with TPU

I printed with TPU.

print with TPU

The sleeves both need to be printed with TPU filament so they can stretch over the jar pieces. Once the pieces are printed, just slide the sleeves over the jar and lid. The ridges and grooves that are modeled into the pieces will hold everything in...

Print with TPU at 40%

Print with TPU at 80%

Print with TPU

... the fixing of the original feet (Flsun_SR_Feet_1.stl) Raises the machine by 2cm, so there is 3cm between the bottom of the machine and the table I printed the 2 parts with a 20% gyroid infill. ... Top printed with PLA and bottom printed with TPU A95.

We recommend printing with TPU

Print with TPU filament at 50%

Print with TPU at 40% infill.

Print with TPU at 90% infill

Print with TPU at 100% infill.

Print with TPU at 100% infill.

Print with TPU filament at 80%

Printed with clear TPU