printrbot plus v1 3d models

I tried chrisantoun14's printer feet but they didn't fit my latest (March 2015) Printrbot Simple Metal's back corners because of rivets, so I decided to make my own. I wanted them smaller and designed to use the clear bumpers I found specifically for...

It is a mounting bracket designed specifically for a Printrboard (Printrbot's electronics board) to fit onto one of the Printrbot's Z motors. To ensure proper fitting, the tabs and their corresponding slots on the main bracket may necessitate...

I did include some ventilation in this design but since my printrbot has a fan mounted on the front, if you don't have one attached you may want to consider adding it when installing this bottom as airflow will be reduced. ...You can find a suitable fan...

Extend your Printrbot Simple's print bed width from 100mm to 140mm, a 40% increase. Ensure holes are drilled and tapped with #6-32 tap set. Use 3/4" x 1/2" angle aluminum for the front brace, and 3/4" x 1/16" for rear. A tensioner with two springs...

I used it for several months until it broke when my PrintrBot fell over during transport in my car. ...Before printing a new one, I made these modifications: - Rounded head - Adjustable guide arm height - Reinforced guide elbow **UPDATE 13...

... rod, M6 brass hex nuts (for smoother operation than standard nuts), a 9mm OD 28.5L compression spring, and vinyl tubing to attach the rod to the z-motor shaft. Tested on a Printrbot Jr., this modification may also work with other Printrbots.

The light holder and blower shroud I built; I discovered that the blower shroud from Printrbot directed too much air onto the actual hot end, so this one works better by directing that air onto the filament instead of the nozzle. For the light, I...

--Make sure to rotate the file so that the top is on the top before assembling--\nI started printing with my printrbot simple metal shortly after unpacking it, only to notice a considerable amount of noise coming from its operation. After testing...

You can also try this: A stand-in for the cord tensioners in late 2013's Printrbot Simple, usually created with laser-cut components 21 and 22. Further information about the part's design is available at http://anoved.net/2014/02/5458/. I printed it...

I accidentally tightened the Z-drive clamps too much on my Printrbot build, resulting in a cracked birch plywood. Unable to find appropriate replacements, I decided to print new clamps while typing this. They're printed without support and should...

I made alterations to elevate and widen it for enhanced stability and less maintenance on my Printrbot Simple. Additionally, I am considering increasing the x-axis platform's depth and lifting it off the ground. ...This change may permit relocating the...

Here are some heavy-duty feet designed for the Printrbot simple metal that stay put and reduce vibration noise when printing on hard surfaces, courtesy of a durable drawer/tool box liner at the bottom. This added feature not only keeps your prints...

Spool Holder for Printrbot Simple Metal using Patio Door Bearings **Get the job done with these essential components!** You'll need one patio door bearing and some 1/4" x 3/4" or 1/4" x 1" bolts and nuts to get started. To ensure a snug fit, wrap...

This dial mount is for your Printrbot Simple, replacing its backplate on a Harbor Freight 1" travel machinist's dial indicator. Mount it directly on the left side of the extruder plate if using the aluminum extruder. The design works well with the XL...

I was struggling with the filament drifting on my Printrbot Simple (v2) direct drive extruder, so I combined the STL version of the laser cut parts and added an extension tube in Tinkercad. Despite these modifications, I'm still encountering issues...

I have some awesome spools of filament from Printrbot and wanted a hub to use with bearings. This thing is that thing. This is an early work. Of the get go I see it could be a little over built in areas and under built in others. ... Update: The...

It's designed to fit Printrbot LC wooden extruder with compatible screws. At .25 cubic inches and .01 pounds in ABS, it's lightweight yet durable. To print, use the given STL file, ensuring all dimensions are in mm. If needed, sand or file mating...

In its beta version, Printrbot Simple had an issue with extruder power wires and thermister wires colliding with the Z screw. A shim was designed to solve this by providing half an inch of extra space between the main body and Printrboard mount. The...

To resolve z-wobble on my Printrbot Simple, I designed a custom coupler shorter than the original, avoiding y-axis motor interference. The flexible coupler is assembled by inserting the tube into the smaller side and adding the lead screw to the...

Obtain a knob and locking nut printable version for your Printrbot Simple v2 with 1/4" Acme threaded rod on Z-axis. The provided .stl file gives both components, as finding Acme nuts can be challenging. Thread the nut onto the top of the Z-rod, then...

This upgrade allows anyone to easily install an e3d hotend on their Printrbot, making it a breeze to work with. I'm specifically using the E3D LiteV6, which fits perfectly on top of the rods. The extruder board mounts the e3d hotend at the bottom, so...

Revise PrintrBot Simple V2 components with 3dtin.com designs at 0.7 scale; flanged cap revisions for spool compatibility, right-angle fan brackets, 30.5mm flanged caps fitting standard PLA spools, reamed 8mm foot/elbows for smooth rod usage, and...

To complete your Maker to Play Upgrade, you must first print the necessary components from Printrbot.com. Ensure that these parts are printed with 100% infill so they emerge as solid objects. ...The quantities needed for each component are: four Z Axis...

I've crafted this secure mounting system for CreativeTool's Universal Filament Filter (http://www.thingiverse.com/thing:492067) specifically designed for the Printrbots extruder. If you're confident in your printer's overhang capabilities, print...

For the first time, I created a 3D item using my Printrbot Simple with Power Tower and Build Area Upgrade, which will arrive next year. I'm delighted with my accomplishment and hope others enjoy it too. After printing, you can smooth out the surface...

The enclosure is specifically designed for a Printrbot LCD screen with an encoder wheel, which can be securely mounted through a laser-cut opening. To enhance compatibility, I made minor adjustments by increasing the size of openings slightly. The...

Having bought a Printrbot Power Tower, I discovered that it only accommodates wooden spools. To store my Ebay-purchased filament spools, I crafted these extensions which work seamlessly with my created spool hub adapters. They were modeled in...

Create a name tag for your Printrbot by downloading this Gothic font from Thingiverse (http://www.thingiverse.com/thing:6820), then inputting your bot's number and finally printing it out. The design features rounded corners, courtesy of...

... the design. This modified model is specifically engineered to be integrated seamlessly under the Printrbot Simple Metal frame, while also incorporating a custom cooling system to safeguard the motherboard and steppers from overheating conditions.

These are the printed housing of a brand-new Printrbot Gear Head Extruder. Stay tuned to this page as more iterations become available. 2/6/15 - we've just released v0.03, which is a fusion of the gear head extruder and the alu extruder. 1/18/15 -...