printrbot simple v2 ninjaflex or other flexible filament guide 3d models

Guide filament pour ender 3 V1 , ender 3 V2 et ender 3 ProCeci permet de guider le filament pour évité des bourrages de fils , de rupture de filament(filament casse) ou encore des sous extrusionCette pièce a été réalisé par MacGiver83 sur le logiciel...

I printed below(2917932), but the base is not so solid and weak(too short), so I remix it with other designs (4570426 & 4823360) Filament Guide_Guide_Open and Filament Guide_Guide_Flat are from 2917932. ... https://www.thingiverse.com/thing:2917932 ...

To print a flexible coupling with ABS hubs and NinjaFlex bellows, use the Flexion Extruder on a Makerbot Replicator at 70mm/s. Overcome dual extrusion challenges by printing an identical part near the printing piece for the idle nozzle to slide over....

Just another filament guide for all Ender 3 models including Pro & V2. Looks similar to the existing guides like 3059604 from MattEllison, but this one slides smooth into place and rests flat on the top rail. To ensure proper printing you should...

redesign of my first filament guide with a longer filament slot to hopefully help with the filament catching or getting stuck if it is kinked or twisted on the roll, plus it looks cooler then the first.

Double roller filament guide which works well with seperate desktop spool holders (or other seperate spool holders).You`ll need:1x bracket2x wheels4x spacers, Additionally:2x 608 roller bearings2x 16mm (minimum) M3 bolts with hex nuts.NOTE: Bracket...

Generic filament guide for CR-10S Pro V2. Parametric. It is intended to snap onto the casing of the filament sensor. Used parts: one 608 bearing, one M5x20mm screw. OpenSCAD source is provided. Note, in the source there is a second version...

Filament roller guide for Creality CR10s PRO V2 and CR10s PRO. ... Components: (x1) Bearing D=22mm d=8mm B=7mm (recommended: SKF 608-2RSL) (x1) Galvanized countersunk screw M4 L=20/25mm (recommended: UNI 7688) (x1) Self-locking nut M4 h=6mm...

A filament guide to help smooth the path of filament as it is pulled into the filament runout sensor on the CR-10S Pro V2. I reused several parts from the Ender 3 version (https://www.thingiverse.com/thing:3052488) but I have swapped out the bracket...

No screws, no supports, 608 ball bearing filament guide designed to fit in the Filboyt filament guide mount. Combine with thing:4683505 (lower) for a complete the set of no screws, no supports, upper & lower filament guides. ... In the pictures the...

This is a filament guide for an Ender 3 v2 that was originally designed with a Bowden Extruder in mind, but if you go Direct Drive and rotate your spool, it'll still work to color filament (End cap won't be needed, but still handy to hold the marker...

Just another filament guide. slip on, so no need for any tools or bearings. ...print without support, and put in place

Remix of Voxelab Aquila Filament Guide by samurai1 , since the previous design was good but the STL was broken in places that only became obvious when slicing.Ended up with a complete remake in Tinkercad but with such a similar design that it's only...

There's another filament guide that's really popular, but I decided to make this since it's way simpler, doesn't require total accuracy, and doesn't require bridging. ... Here's the Onshape link:...

Combined these to filament guides into one for the CR-10 V2 https://www.thingiverse.com/thing:4683505 https://www.thingiverse.com/thing:4023754 I liked the big roller from Markacho's design and wanted that for my CR-10 V2, so I used gmuddy's mount...

The friction provided by the tightened screw connections is enough to keep the filament guide in place, because the acting force of the filament on the barrel is not pulling the guide in the opposite direction of the slots. - Increased the...

Wanted a mount for my Ender 3 v2 with an integrated connection for a Bowden guide

Bras guide filialement pour la ender 3 v2 neo avec ou sans sigle. ...

You can either print the complete set or only the modified base.The modifications of the base include:Increased diameter of the screw holes, so no need for tapping through them or enlarging them after the print.Redesigned the two screw holes as slots...

Yet another filament guide for your Ender 3 V2. Not much filament and printing time required, a single screw M4 x 15 (in ender 3 V2 kit as spare) and a ball bearing 689RS (9 x 17 x 5). Supports required for the arm, check out in the pictures how...

Bottom Filament Guide for Ender 3 V2 Neo. This is a remix of two designs taking the best element of each. https://www.thingiverse.com/thing:3010366 https://www.thingiverse.com/thing:4648991 PLA is strong enough. ... Carefully remove Z axis...

This is a simple filament guide I made because I did not like that the filament would rub against the Z-Axis Guide Rod when printing. To mount, all you do is remove the 2 screws beside the guide rod and slide the piece over. Once done, reinstall the...

This filament guide is designed for Ender 3 V2 extruder with default top spool holder in mind. The ones I've printed is made of PETG. Function-wise, it is designed to prevent filament breakage when the filament angle between extruder and the spool...

This is a filament guide for the Ender 3 V2 printer. The guide aims to reduce stress on the filament, straighten out the entry into the extruder, and avoid rubbing against the z-axis screw. This is an update to a previous design using heat inserts...

This is an upper filament guide that I designed for a Creality CR10S Pro V2 printer. It was designed for use with a 7mm x 22mm x 7mm bearing. The static upper guides all work great, but I wanted something to aesthetically match the lower filament...

I had extrusion problems that made me babysit my first many prints, i eventually realised that this was caused by the original filament holder of the ender3 V2, since it had a tiny bit of resistance when turning the spool, i resolved this issue by...

This is a simple remix to reduce how far out the filament guide extends away from the printer so that it can fit in a standard tent enclosure. ... The big thing though is that it has an updated plug which is a much more snug fit and won't fall out as...

This filament guide holds the filament out from the printer 100mm and pushes it back about 50mm

Their guide was a great idea but it did not line up with the extruder great on my Ender 3 v2 and I also wanted to use a 6000 bearing I already had laying around so I modified their design a bit. The parts you need are 6000 bearing and M3 bolt with...

-------------------------- Here is a filament guide for the CRS10 PRO / PRO V2 that doesn't need a bearing and is fixed using 2 screws from the filament sensor block. It's a remix of the https://www.thingiverse.com/thing:4127961 Filament Guide: I...