pro x motors 3d models

After I had some serious layer shifting I found that my wiring had gotten too loose on the plug into the X motor. So I designed a strain relief to fix the problem, I also put the X endstop wiring through it so it has no strain either. ... One small...

After I had some serious layer shifting I found that my wiring had gotten too loose on the plug into the X motor. So I designed a strain relief to fix the problem, I also put the X endstop wiring through it so it has no strain either. ...One small...

Do not under estimate the power of the dark side! ... Got tired of the QR code on the X-motor cover, so I designed a cover for it. ...Maybe someone else fancy some dark side powers for their Ender 3/Pro

this is an X axis motor mount for your prusa I3, you can use it on the printer like the geeetech prusa I3 pro& pro B or pro C,http://www.geeetech.com/3d-printer-3d-printer-c-24_98.html

Just a remix with a w40k logo. Thanks for the original work! ... I only printed the inset version of this design so far and glued the right half of the skull back to the cover, because the led would be a bit too bright without.

... the heatsink to reduce the temperature of the motor. This part is mounted in the original extruder housing and helps cooling with the 40x40x10 fan at the end. What's needed PETG, PLA PRO or PLA+ filament Heatsink suitable for motor 40x40x10 24v fan

I lost one of my ribbon cable clips, so I designed a new one as a spare part. ...This clip fits for the ribbon cable at the X axis motor on the left side of the frame.

A cover with a cable mounting point to go over the x-axis stepper motor for the Creality Ender 5 pro. ...This is to help with strain relief and to stop the cable rubbing.

Secure the motor to the metal plate first, and then the cover. ... The screw holes for the endstop can be M3 thread (heat) insert.

<p>Remixed to fit Flex Tubing and also made channels for the cable ties instead of having the go all the way through.</p> Category: 3D Printer Accessories

Remixed to fit Flex Tubing and also made channels for the cable ties instead of having the go all the way through. *Note: When I remixed and printed I realized the cable was showing in the front. This is what is shown in the picture. ...I fixed it...

I wanted to make this part stronger! ... As a lot of guys experienced, the acrylic cut was awful condition... They need to fix their laser-cut system I guess :3 Mk2 contains reinforcement structure which allows you to avoid the motor from sagging!

I liked this improved version on the original Y motor mount on the Geeetech, but I wanted to get rid of the additionnal part on the side, that I had to cut with the dremel post printing. ... Here is a remix version without the mentioned part.

Remix / recreation of https://www.thingiverse.com/thing:4852456, that allows you to remove the top front bar of the X5SA (pro and non pro) and reroute the belts so that they don't interfere with your view of the printhead/printjob. While I have...

You will need to mod the carriages as per the original thing, you will also need to relocate the Y endstop and extend the motor cables. I heavily advise that you reinforce the corners of your printer, as removing the top bar wlll probably make the...

... thing to upload to please feel free to leave any feedback and upvotes. It dropped my decibels by about 5dB. Use a soft material like TPU for these. Here is how it should be set up: Without Damper - Motor | Mount With Damper - Motor | Damper | Mount

I also increase the size of the recessed area as the belt was not properly aligned with these dampers I bought: https://www.amazon.com/dp/B083JTC6JJ/ It fits perfectly now, and if the recessed area is too marge and the motor sits two far into the...

This is my self made motor cover for the X Axis V-Belt. Supports arent requied. ...Rotate by 90 Degrees, the flat side should be on the printing bed and the complex side should facing upwards.

... i used: http://www.thingiverse.com/thing:1556884 Version2: The space for the Motor Connector was too large, so i reduced the space for better fit. Print Settings Printer: Geeetech prusa i3 pro B Rafts: No Supports: Yes Resolution: 0.2mm Infill: 20%

Additionally, they are forcing the Y motor pulley to be positioned unnaturally high, creating a lever effect and bending both shaft of the motor and the bracket as well if we overtense its belt even a bit.&nbsp;To resolve that issue I created thick,...

Ender 3/V2 X-Axis Motor/Limit Switch Cover for Sprite Extruder Pro Kit con el simbolo de zelda

This is a remix for x-axis stepper motor cover for Ender 3/Pro/V2. ... I have also provided a base model stl file for easy remixing with new logos.

Summary This X-Axis Motor/Limit switch cover corrects the issue with the carriage that comes with the Creality Sprite Extruder Pro Kit. The limit switch using this is moved an additional 6mm away from the carriage, giving you bed space back. Screw...

This X-Axis Motor/Limit switch cover corrects the issue with the carriage that comes with the Creality Sprite Extruder Pro Kit. The limit switch using this is moved an additional 6mm away from the carriage, giving you bed space back. Screw Mounts are...

(most notably the single Z axis motor upgrade designed by RRacer, i have also modified that design and that can be found on my uploads page). I recommend 5 perimiters with at least 30% infil to keep it fairly sturdy. I have printed mine at 0.2mm...

Motor protection for Phantom 4 Pro

- V2 : fixed some falws - Mini Mavic Pro - Made for 7mm brushed motors - Compatible with 7x20 and 7x16 motors

Local Motors recently started selling the Estes Proto X in our retail stores and on our website, http://www.localmotors.com/shop. Inspired by this thing: http://www.thingiverse.com/thing:214642, we decided to try to make our own case, which we may...

This cover clips onto the Eder 3 Pro x-axis motor.

- Mini 3D printable Mavic PRO for tiny brushed motors ! ... - V2 : fixed some falws - Compatible with 8.5mm motors