professional drag chain cable changeable in scad width height 3d models

Mounting bracket for a standard 10x11mm drag chain (from Amzn) for the Atomstack A5 Pro. ...The picture shows the V1 which was not sturdy enough but the .stl is V2 which is strengthened at the sides.

Here are the drag chain parts that I designed for my MPCNC Primo. ... You'll need to figure out just how many links that you will need for the size of your CNC.

Shapeoko 3 bracket securely attaches to the drag chain at the Y rail position. ...The bracket expertly mounts itself between the rail and the control box's protective cover plate.

habe zusätzlich eine mit Bohrungen erstellt (wenn andere Maße benötigt werden, kann ich die Löcher versetzen) ------------------------------------------------------------------------------------------------------------------------ English: I...

I reused a worn-out electronics shroud as the foundation for my drag chain anchor, adding custom top and bottom covers to block debris from entering. While designing this setup and learning the ropes, I observed that my motors were overheating,...

... Works with regular 10*20mm drag chains available everywhere on the internet. I used this one https://www.amazon.de/gp/product/B07S6LW7BK/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1 M3 T-Nuts, as well as bolts are required for mounting. ...

These are three attachment fittings for to add drag chains to many Atomstack laser engravers such as the X20 Pro, S20 Pro, A20, Pro and I think A7 and any laser engravers with the same stepper motor mounts. These are designed to work with the drag...

3D printed post to mount a drag chain on a K40 laser cutter to support the air hose for an air assist and keep it from touching the laser beam. ...Attached text file has directions.</p> <h3>Print instructions</h3><h3>Print Settings</h3>...

This is a remix of the carriage mount for the drag chain by OpenDorrPolicy. it was created because I found the original mounting solution to be a bit too fragile in regards to the clip on mechanism. On this remix, it has been replaced with a solid...

Made this to go with Drag Chain HD by BikeJunky on here. http://www.thingiverse.com/thing:568551 Clamps onto one of the z-axis to allow mounting of the chain. Uses M3 Hardware. Needs M3x25 for the clamp and lock nut [I'm going to try a zip tie first...

Print in pla .4 nozzle and 0.2 layer height and enable support . This link allows removal of the bridge if you need to change wires around, without removing the complete chain. ...Very handy when setting up

This is a drag cable mount, which replaces stock ribbon cable support for Creality Sprite Pro Extruder. It will give you much better cable management and will not hit any of axis. My E3Pro still has 235x235x250 active printing area (with reversed...

I wanted a drag chain rear mount that wouldn't force me to drill into the chassis. This versatile mounting solution allows for both horizontal and vertical chain orientation, giving users maximum flexibility. Conveniently, a set of pre-drilled...

The dimensions of the 3D object are preserved in their original state, allowing for any desired modifications to be made. ...Additionally, the raw object file has been included, enabling users to experiment with it; however, please note that this file...

... it was all I had available. I used a 2" long #10-32 screw and nut to join the two pieces together. Normally, I would print holes for attaching the drag chain, but since there are various styles out there, it's simpler to just drill what you need.

The new QueenBee Pro CNC router kit from Bulkman3D includes their drag chain kit with the purchase. However, this kit doesn't seem to come with the hardware required to mount to the QueenBee Pro, which has different extrusion end brackets than the...

The newest model, The "Spine Chain", is available here: https://www.thingiverse.com/thing:2785330 You'll need the following parts: 21x chainmail.stl 1x Modular_x_chain_support.STL 1x chainbegin.STL If you don't have the modular X carriage, it's not...

The holes also did not fit with the chain I used : https://www.amazon.fr/gp/product/B07Y6769LL/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1 I also drilled a hole in the chassis to better route the cables and avoiding to change them. ... You will...

These Mounting Holders are specifically designed to securely attach the CK15 drag chains directly to the Shapeoko-X without requiring any drilling or modifications. ...To achieve this for a Shapeoko-X measuring 50x50cm, we utilized 27 components of CK15...

... an original part from the Shapeoko XXL. ... This bracket is extended to 8 inches long parallel to the Y1 belt and 1.4 inches to prevent drag chain fall-off and hooking. ... I printed this with 8 perimeter walls and 40% infill for increased rigidity.

Designed specifically for an Ender 3's Z axis, this custom bracket/mount seamlessly accommodates my store-bought 10x15mm drag chain. Originally intended to pair perfectly with a Bantam Feeder, it also offers compatibility with the stock extruder.

I sought out a drag chain mount that wouldn't necessitate disassembling my extruder motor, which was a major pain point. To resolve this issue, I modified the existing clips to accommodate zip ties instead of traditional screws. ...This modification...

This is a holder for a 10x20mm drag chain for the K40 lasercutter. It can be printed without support structures and can be fixed with the one existing screw. ... See also my air assist nozzle for the K40 lasercutter thing:4753879

Attach a Simple Y Drag Chain Holder to your Shapeoko 3. You'll need to drill two holes into the Sideplate. ...The holpattern is designed for 30mm IGUS dragchains, which you can purchase on Amazon here: https://www.amazon.com/dp/B07V1G4RMP

... Once on the extrusion you can screw in the top screw. the bottom screw may require sanding or filing of the head so it does not rub on the extrusion. I have also included a drag chain mount for the hemera, and a mount for a 8mm pinda probe.

I tried printing the drag chain links from johnniewhiskey, but the links didn't move as freely as I wanted them to. I came across this remix from Yeggster and they worked much better. I needed them to fit on a 3/4" rail so I resized them. They are...

-----------------------------------English--------------------------------This is an adapter for attaching a drag chain (10x20mm) for the X-axis.One holder is attached to the Z-axis and the other to the X-Carriage. No holes have to be drilled or the...

Customized Version of a Thingiverse Design Created with the Customizer App Instructions to Use the Following Options: To Assemble This Project, Follow These Steps: Use Link Width Option: Set to 15 for Optimal Performance Define Polygon Density:...

I wanted to make a simple, and easy to print drag chain for a project I'm building. Other designs I had found required multiple parts or microscopic clips for each section of the chain. Others required large amounts of support material and were hard...