professional drag chain cable changeable in scad width height 3d models

Mounting bracket for a standard 10x11mm drag chain (from Amzn) for the Atomstack A5 Pro. ...The picture shows the V1 which was not sturdy enough but the .stl is V2 which is strengthened at the sides.

... Works with regular 10*20mm drag chains available everywhere on the internet. I used this one https://www.amazon.de/gp/product/B07S6LW7BK/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1 M3 T-Nuts, as well as bolts are required for mounting. ...

These are three attachment fittings for to add drag chains to many Atomstack laser engravers such as the X20 Pro, S20 Pro, A20, Pro and I think A7 and any laser engravers with the same stepper motor mounts. These are designed to work with the drag...

Created this clip for the Kevinakasam Belt Drive mod to allow for attaching a drag chain from this model: https://www.thingiverse.com/thing:4316238/files. This would replace one of the belt retaining clips so that you may run a drag chain from the...

i made this to connect drag chain i found on thingiverse to my printer cr-10 v2 profile without using screws or insets but it can connect any 40mm rail anyway holes are prepared for those who want to use them but it is very strong no need for any...

I reused a worn-out electronics shroud as the foundation for my drag chain anchor, adding custom top and bottom covers to block debris from entering. While designing this setup and learning the ropes, I observed that my motors were overheating,...

habe zusätzlich eine mit Bohrungen erstellt (wenn andere Maße benötigt werden, kann ich die Löcher versetzen) ------------------------------------------------------------------------------------------------------------------------ English: I...

This is a remix of the carriage mount for the drag chain by OpenDorrPolicy. it was created because I found the original mounting solution to be a bit too fragile in regards to the clip on mechanism. On this remix, it has been replaced with a solid...

Here is a highly advanced semi-closed 15mm x 15mm drag chain perfectly designed for my top-of-the-line 3D printer. ... I employed Core3D.tech's cutting-edge technology and meticulously edited the original model link to ensure a precise match with the...

Print in pla .4 nozzle and 0.2 layer height and enable support . This link allows removal of the bridge if you need to change wires around, without removing the complete chain. ...Very handy when setting up

This is a drag cable mount, which replaces stock ribbon cable support for Creality Sprite Pro Extruder. It will give you much better cable management and will not hit any of axis. My E3Pro still has 235x235x250 active printing area (with reversed...

I wanted a drag chain rear mount that wouldn't force me to drill into the chassis. This versatile mounting solution allows for both horizontal and vertical chain orientation, giving users maximum flexibility. Conveniently, a set of pre-drilled...

Drag Chain Designed to Guide Small Cables or Filament Tubes Dimensions: Inner Height: 5.1 mm Inner Width: 5.1 mm External Height: 8 mm External Width: 9.1 mm I created this drag chain because I couldn't find a suitable design for small applications...

Remix from @diogosantos88 design and this https://cults3d.com/fr/mod%C3%A8le-3d/outil/ender-3-v2-satsana-bltouch-hotend-cable-chain-small-mount

... it was all I had available. I used a 2" long #10-32 screw and nut to join the two pieces together. Normally, I would print holes for attaching the drag chain, but since there are various styles out there, it's simpler to just drill what you need.

A replace for the little arm that holds the vertical (bed) drag chain to the bed carriage.The holes for the chain are placed 10mm nearer the bed, so the chain shouldn't tangle with the upper aluminium extrusion.Instead of doing a simple block with...

The new QueenBee Pro CNC router kit from Bulkman3D includes their drag chain kit with the purchase. However, this kit doesn't seem to come with the hardware required to mount to the QueenBee Pro, which has different extrusion end brackets than the...

This is a highly anticipated 'Z' Axis Cable Chain for the Ender 3.\r\n\r\nIt's currently in development, as there's one obstacle to overcome - the wiring provided with this 3D printer is too short to be used with a cable chain. I must figure out how...

The holes also did not fit with the chain I used : https://www.amazon.fr/gp/product/B07Y6769LL/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1 I also drilled a hole in the chassis to better route the cables and avoiding to change them. ... You will...

These Mounting Holders are specifically designed to securely attach the CK15 drag chains directly to the Shapeoko-X without requiring any drilling or modifications. ...To achieve this for a Shapeoko-X measuring 50x50cm, we utilized 27 components of CK15...

I remixed the SuperSniffles contribution Eva for the vCore Pro and mounted it on the the XY Joiner left from RatRig vCore3 https://contrib.eva-3d.page/cable_chain/xy_cable_chain_mod/ My poor CAD skills didn't allow me to make it printable without the...

I ordered a Drag Chain and needed a couple of end pieces..Befenybay R18_internal size 10x15mm_outside openI didn't chamfer/countersink the mounting holes….I may add the chamfered models if neededThe picture shows….Black parts are the originals and...

... an original part from the Shapeoko XXL. ... This bracket is extended to 8 inches long parallel to the Y1 belt and 1.4 inches to prevent drag chain fall-off and hooking. ... I printed this with 8 perimeter walls and 40% infill for increased rigidity.

I sought out a drag chain mount that wouldn't necessitate disassembling my extruder motor, which was a major pain point. To resolve this issue, I modified the existing clips to accommodate zip ties instead of traditional screws. ...This modification...

This is a holder for a 10x20mm drag chain for the K40 lasercutter. It can be printed without support structures and can be fixed with the one existing screw. ... See also my air assist nozzle for the K40 lasercutter thing:4753879

Attach a Simple Y Drag Chain Holder to your Shapeoko 3. You'll need to drill two holes into the Sideplate. ...The holpattern is designed for 30mm IGUS dragchains, which you can purchase on Amazon here: https://www.amazon.com/dp/B07V1G4RMP

****ESPAÑOL****Transportador de arrastre por cadenaCapacidad: 60 TPHVelocidad lineal: 0.808 m/s62 RPM****ENGLISH****Chain drag conveyorCapacity: 60 TPHVelocidad lineal: 0.808 m/s62 RPM****OTROS MODELOS/OTHER MODELS****Bearings from SKF website:...

Designed specifically for an Ender 3's Z axis, this custom bracket/mount seamlessly accommodates my store-bought 10x15mm drag chain. Originally intended to pair perfectly with a Bantam Feeder, it also offers compatibility with the stock extruder.

... Once on the extrusion you can screw in the top screw. the bottom screw may require sanding or filing of the head so it does not rub on the extrusion. I have also included a drag chain mount for the hemera, and a mount for a 8mm pinda probe.