professional drag chain cable changeable in scad width height 3d models

MPCNC Primo cable chain mounts. ... Fits cable chain up to 1.45" in width. Use 1.5"x1.5" Aluminum angle for the z support. Requires longer hardware than what is included in the kit for the XY chain mounts. ...(2" bolts)

Cable Chain Mount.

... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=915487 Instructions Using the following options: number_of_links = 12 anti_stick = 0.20 link_width = 22 $fn = 150 link_height = 6 part_selection = 1 shell_thickness = 2.5

... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=915487 Instructions Using the following options: link_width = 18 link_height = 5 anti_stick = 0.15 $fn = 140 part_selection = 1 shell_thickness = 1.8 number_of_links = 14

... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=915487 Instructions Using the following options: number_of_links = 16 part_selection = 0 $fn = 140 link_height = 5 shell_thickness = 1.8 anti_stick = 0.15 link_width = 18

Customized Version of Thingiverse Object 915487 Created with Customizer Tool on Thingiverse Instructions Utilizing the Following Options: shell thickness - 1.8 mm link height - 5 units part selection - default setting (0) anti-stick coating - 0.15 mm...

This is a remix. ... I remodelled the part lifting the chain mount connection position about 10mm.

I printed in PLA, any material is ok.Please note than I had to print a new board support in order to move usb cable on the right allowing to put the board on the left. ...This is needed to shorten the path as much as possible otherwise new motor cables...

Plus, It's Designed to Print Two Layers (with 0.2mm Layer Height), Making It Easier to Remove After the Print Finishes – Especially Important for Textured Sheets and Filaments Where the First Layer Height Was Originally Too Low, Leaving a Thin Smear...

It is designed to print two layers (with 0.2mm layer height) so it is easier to remove after the print finishes (especially important for textured sheets and filaments where the first layer height was originally too low leaving a thin smear of...

Customized Version of Thingiverse Design Created with Customizer Tool: http://www.thingiverse.com/apps/customizer/run?thing_id=915487 Instructions Using the Following Options: Number of Links Set to 8 Circular Resolution Defined as $fn = 140 Link...

A not so flimsy alternative for drag/cable chains for the Neptune 3.Requires replacing the original filament sensor holder and bed connector, would therefore recommend printing at least the latter one in ABS/ASA.Shown are printed in ABS

This is a very basic mount to be screwed on the 25mm pipe-ends of the MPCNC Primo 25mm version to easily attach dragchains, cables or dragchainsupports. If you want to use them on both ends of the tube, please mirror the model in your slicer and...

Cable Chain Management parts for the Prusa i3 : These are mostly re-works or improvements made on some things found & adapted for the Prusa i3 & as such are a work in progress. Revised & strengthened version of Chain Link by bqLabs : + Original Drag...

I Made a Remix for the X5SA 500 Pro wit a guide for the Chain. ... It sabelize it and it's not going down on the Belts

This is a remix plus some additional parts for mounting the chains to the trucks for X and Y chains. I used M3x30mm screws (x2 per truck) for the added truck mounts to replace the original M3x10mm screws on two of the corners of the stepper. I...

This is a remix. I remodelled the part lifting the chain mount connection position about 10mm. Category: 3D Printer Parts

I place my new printer on an uneven table and, inspired by that, I designed these adjustable height feet for my FlyingBear P905. ...To make them, I need four sets of feet, four M4 x 35 screws, and eight nuts.

Chain Holder for Atomstack Laser. It's a Remix from Ricardo1980's holder. Nr 2 and Nr 4 are the same holder. ...Holder Nr 1 and Nr 3 are screwable.

This is a very basic mount to be screwed on the 25mm pipe-ends of the MPCNC Primo 25mm version to easily attach dragchains, cables or dragchainsupports. If you want to use them on both ends of the tube, please mirror the model in your slicer and...

Attached the Prusa X Axis Cable Holder to the Cable Holder Guide. The other components appear to be compatible with the MK3, although I haven't conducted any tests yet. ...If you successfully assemble it, kindly share your experience and let me know if...

I really have no idea what I'm doing, but I saw a reddit post of a drain chain I like, and I'm trying to get that going! Please use this as reference only, as I'm horrible at 3D design. I'm hoping to get this finished product to look like this....

Effortlessly create chains in SolidWorks with this straightforward method.

https://www.facebook.com/groups/573927206446790/ The following items are included: - Tow strap 10x10mm inside and 14x17mm outside - Tow strap 10x20mm inside and 15x27mm outside - Two small cable ties - Six M3x10 screws with nuts (hotend, counter...

11/04/17 Added step file After hours of searching and printing to find a cable drag chain for my reprap I decided to make my own. Why? ... 1) Needed to be small this one can do 180 degree turn using 5 links with a total width of 45mm 2) Cables enclosed...

... felt like redesigning the extruder end was easier than redesigning the hotend piece as I already liked the original from diogosantos88 & OpenDorrPolicy. The height difference seemed to be about 12mm so i made the adjustment Hopes this helps somebody

Easy to Print Cable Chain

Cable chain for Zonestar Z6FB

Diret drive cable chain start

I did not find it useful, so I did not export it as STL)[width]. The width of the cable slot.[height]. The height of the cable slot.[depth]. The depth of the cable slot. (The hinges are not included in the depth, so the total depth will be...