professional drag chain cable changeable in scad width height 3d models

While I designed the "Up-size Clip" to snap onto my 18 x 14mm (H x W) cable chain, you should be able to scale the STL file during slicing in X & Y as needed to work with larger or smaller cable chain sizes. If not, the source SolidWorks (2013),...

Print the following quantities: (1) z-chain-frame.stl (2) half-inch_emt_insert_2mm-rev3.stl (1) z-chain-gantry2.stl (1) half-in_emt_mount2.stl (?) cable_chain_link.stl (?) cable_chain_clip.stl Purchase Parts: (2) 6-32 x 2" screws with nuts (2) 6-32 x...

No matter how careful I am, No matter that I start a new LONG Cable Chain with a Male connector, SOMEWHERE in the process I'll be ready to do my final connection(s), and realize that I'm staring at a Female Cable Chain end in my left hand, and...

Parts needed: Open Drag Chain from https://www.thingiverse.com/thing:2146995 18 Link.stl 18 Lock.stl You can also use https://www.thingiverse.com/thing:2498801 for the upper part, I've simply merged the files together. Upper Part: I've updated the...

If you printed the previous version and you have no issues, there is no need to download this new version.If you want to protect the long cables of your Elegoo Neptune 4 Max and prevent them from hindering your prints, tangling on them or hooking...

the archive contains : V4 front version V4 version and higher version with original wires (vertical model 17 links) version with extended replacement wires (horizontal model 20 links less stress) the installation instructions necessary equipment: 17...

Use this alternative UMO Cable Chain adapter if you want to use Robert's UM2 cable chain: https://www.youmagine.com/designs/ultimaker2-cable-chain. This design is intended for DIY heated beds. First, attach the chain adapter to the mounting bracket...

Parts: Open Drag Chain from https://www.thingiverse.com/thing:2146995 18 Link.stl 18 Lock.stl You can also use https://www.thingiverse.com/thing:2498801 for the upper part, I have just merged the files. UPPER PART: Updated mounts for NEMA 34mm long...

... thickness, with 100% infill and a print speed of 40, and it took eighteen hours to complete the process. The internal dimensions are substantial: twenty-four by nine point five millimeters in size. ...This chain is extremely loose and flexible.

Six rows of sturdy six-link cable chain cables are securely attached with a robust ten-millimeter internal diameter. A carefully crafted custom brim, a thin yet strong twenty-five-micrometer strip, seamlessly connects each link to prevent them from...

... a cable chain Y-axis system on my Anet A6 3D printer. ...The level sensor is mounted on the front, and I've also got a cable tie hole in place. ...To complete this setup, you can use the elements found at https://www.thingiverse.com/thing:611593.

####Cable chain setup for hotbed and x-axis harness:#### + The slim link should be **cable tied** to the existing hotbed mount. + The wide chain top mount requires **no additional hardware**. Its attaches to the existing x-axis spindle screws. ...This...

It has a latch that allows you to easily arrange and close the cables. * * * #####Demo video: https://youtu.be/ofkW5O3-xkM * * * #####Status of this project: - First release v1.0 printed, and after testing - 2022-02-27 update to v1.1 printed,...

... 3. ...These brackets allow the user to attach 15x11 cable chains to the frame of an ender 3 and a bmg styled extruder for better cable managementFor more Information check out my grabcad https://grabcad.com/library/cable-chain-brackets-ender-3-1

... plates... the original cable chain brackets didn't have enough thickness to nicely mount. There was a 3mm gap between the bracket and the chain extrusion support on either side. ... This is simple remix that thickens the chain side of the bracket.

Cable Chain for Printer Discovery 200. I utilized the following chain: http://www.thingiverse.com/thing:11978. This modification necessitates lengthening all wires originating from carriage X. It requires thirteen links for the vertical chain,...

... My bed size is 300mm x 300mm and I used 38 cable_chain_link parts and 38 cable_chain_clips. ...Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2mm Infill: 20% Filament: Zyltech PLA Black Category: 3D Printer Accessories

** The base connector has been updated to one piece under the name "cable_chain_base_new.stl" (seen in photo 12). Supports will be needed for the overhang of the tube, which I achieved with a 75-degree angle. ... To assemble, thread the cable through...

The cable chain is elevated 5mm above the highest point of the gantry, ensuring that both the extruder and gantry ends allow for smooth bi-directional swinging, preventing cables from getting tangled in a tight arch when the head reaches its maximum...

I needed to adapt the drag chain mount of workbee CNC machine for my drag chain (18x37). I reinforced the mount because the one i previsously had broke too easely. ...I can send you yhe orginal fusion objet if you want.

The cable chain is a remix of: https://www.thingiverse.com/thing:644420 I keep the bottom of the chain held in place with a magnetic block. http://www.michaels.com/pro-mag-neodymium-magnets-.5%22/10382640.html Update 07-09-17: I reprinted this in...

Cable management system designed specifically for the Prusa i3 3D printer features a durable cable chain that securely fastens cables and wires to the printer's frame, keeping them organized and within reach. ...The cable chain is adjustable to...

WIP Z Cable chain Slips over bearing and is secured with an m3 grub screw (make sure it is not too tight to dent the bearing) 10mm cable chain used from mellow Aliexpress store

Finally an Ender 5 Cable Chain mount that works with Microswiss Direct Drive! ... Yay! I used this cable chain https://www.amazon.com/gp/product/B07SFFT1K5/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

Double Female Cable Chain Link... ...another remix from johnniewhiskey's EXCELLENT Cable Chain System, found here: https://www.thingiverse.com/thing:2920060 For a Double Male Link, see my other remix at: https://www.thingiverse.com/thing:4758733

Hello. ...After cutting out a Tatara A8 frame with a laser cutter, I discovered that my previous Y cable chain no longer fit. ...So, I designed brand-new components to fit the old cable chain onto my updated frame.

So I came up with the idea to add a vertical cable chain, getting the cable right out of the way and in my opinion looks a lot neater. ... **NOTE:** I ended up having to print 26 chain links and having to cut the aluminium channel to about 580mm...

Engineer installed opposing side offset mounting tab on Cable Chain End to enhance structural integrity of the A5.

Cable clip for these chain mounts: https://www.thingiverse.com/thing:4936501 https://www.thingiverse.com/thing:4936499

Cable chain attachment for the Sapphire S printer. ...A part list is included with the exploded drawings.