professional drag chain cable changeable in scad width height 3d models

Customized version of https://www.thingiverse.com/thing:4375470 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4375470

Customized version of https://www.thingiverse.com/thing:915487 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=915487

To get started, use the instructions from the stock Prusa frame's chain files as a reference point, then mix things up by remixing them entirely. Take note that you'll be working with a new, shorter chain path that reduces weight on the extruder and...

... long hollow, short). You can print Big 0.2, 0.25, or 0.3 layer height. For Small 0.2, 0.25 layer height. 2 perimeters with extrusion width 0.4. No infill, no supports. ...I use Kisslicer, but can be sliced with any other slicer with this settings.

... printer's settings. ...I've also completely eliminated the pin hole to eliminate unnecessary friction, resulting in a chain that bends more easily. ... Print Settings Printer: Graber i3 Rafts: It Doesn't Matter Supports: No Resolution: 0.3 Infill: 20%

... was created using the Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=1078216. ... Instructions for Using the Options: The following settings were used: Length: 25 inches Width: 16.6 inches Radius: 1 inch Height: 13 inches Type: 2

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1078216 Instructions Using the following options: Type = 1 Round = 1 width = 20 length = 25 height = 15 Category: 3D Printer Parts

http://www.thingiverse.com/apps/customizer/run?thing_id=1078216 Instructions Using the following settings: Type is set to 2 ChainDef is defined as [[1,0]] width is adjusted to 25 Round has been increased to 1 length is fixed at 25 height is precisely...

Under bed mount for CR10-S Heated bed cable

Altered the link for installation without disconnecting the cable.

I had originally used a simlar chain by eddiema: https://www.thingiverse.com/thing:40918 but needed max 17mm and so the scaled down version was not so good (too loose). Then I found this version but there were no end parts. Hence I used the design...

height testing for new printers

You can never have enough of these small cable wraps to connect to your aluminum extrusion.

... <p>Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1078216 Instructions Using the following options: Type = 1 Round = 1 width = 20 length = 25 height = 15 Category: 3D Printer Parts

Needed a dual open ended link for a piece of my chain, so I made one myself

The cables from my Ormerod 2 started sagging onto the build plate, bringing printing to a standstill. ...To solve the problem, I designed and printed a custom cable management system that secured the cables safely over the extractor fan.

I initially employed a chain by eddiema, but required max 17mm and the scaled-down version was not satisfactory (too loose). Subsequently, I discovered this alternative version by Codiacx at https://www.thingiverse.com/thing:511938. However, there...

That's why we're printing wire chains like traditional manufacturing. My answer is straightforward. Prints as a single piece. No supports required. Wires can slip in, and there's no need to thread them through. Then, connect the ends with an M3 to...

I originally employed a similar chain by eddiema: https://www.thingiverse.com/thing:40918, however I required max 17mm and consequently the scaled-down version was not ideal (too loose). Subsequently, I discovered this version but unfortunately it...

You can never have enough of these little things to help wrap and hold your cables on the aluminum extrusion.

... about as simple as it gets for a cable holder. ... Screw this to the underside or side of a desk and snap a usb charging cable through the keyhole slot. ... It's a quick print that has saved me from crawling under my desk looking for a charging cable.

I know that there are many models of cable links but for my cnc I wanted something really flexible and with a radius of curvature well controlled, hence this creation, for the model most one wearing a closure system difficult to reopen (this is the...

45° per link, to shield cables from snapping.\nFor bending to both sides, visit: http://www.thingiverse.com/thing:722175\n UPDATE: A new link design is available online, with a removable outer diameter side! ...This change increased the inner part's...

The oversized design ensures that cables can be secured safely, preventing accidental disconnection as the telescope moves, thereby protecting the delicate socket from damage.

... clamp and compatible with Nema 23 motors. ...Two variations are available - one using a single chain and the other employing a double chain. ...All components required can be found at Thingiverse under this link: http://www.thingiverse.com/thing:11978.

... model a bit. <h1>Update 03/10/2023</h1> * Reworked the baseclip to be more robust and to better guide the sleeve to the right direction. * Changed the chain piece to add flexibility to the chain and separated link and clip to serparate files

Sometimes the lid of these kind of canisters is very hard to open the first time around, or it gets stuck with sticky fluid in the cap. One file has the complete model in one part. The other 3 files are for printing it in multible colore. Note that...

Some cable carrier will be warped after installation, and rub against the toolhead, use this to clamp them

Here's a link to a straightforward enclosure for a cable harness: https://www.thingiverse.com/thing:1298527

Here is the second part of my cable supports which you can find here https://www.thingiverse.com/thing:4335239, but this concerns the cables of the heating bed. Still no need for additional screws. ...The links are not closed to allow the passage of the...