proform treadmill tablet holder 3d models
337908 3d models found related to proform treadmill tablet holder.thingiverse
... close to the panel so lager tablets could fit. The original plan was one wide piece but two smaller ones seem to work better. I suspect other Proform and Nordic-track treadmills use the same tablet holder so this might work for other devices. ...
thingiverse
The ProForm 580 treadmill does not have a tablet holder, this is a solution and does not block the cooling fan. It was made for 7" to 8" tablets, but would probably work with a 10" tablet in a pinch. There are numerous reinforcing ribs on the...
grabcad
The stock Pro-Form Carbon CX tablet holder is too narrow to hold any tablet with a case on it. I designed this one to be sturdy, and to hold nearly any size tablet. I have printed this and it works great. ...There is a left and right side.
thingiverse
This is an iPad holder for my treadmill. It screws onto console and holds tablet/book at a convenient angle. All the parts are printed in ABS and solvent welded with Acetone. ...The incline angle on treadmill console is 30 degrees.
thingiverse
Frame to hold a laptop/tablet on your treadmill arms so you can work and exercise at the same time. Uses three pieces of aluminium available from your local hardware store, 25.4mm tube for the cross piece and two 40x20mm for the two other pieces.
thingiverse
Replacement key for a Pro-form 385c power incline treadmill. Simple, fast print. ...Works fine.
thingiverse
The tablet holder that comes installed on the Pro-Form Carbon CX bike is not wide enough to hold any tablet with a case on it. I made this sturdy 2-piece replacement to hold just about any tablet. I've been using it for a couple weeks and it works...
cults3d
The tablet holder that comes installed on the Pro-Form Carbon CX bike is not wide enough to hold any tablet with a case on it. I made this sturdy 2-piece replacement to hold just about any tablet. I've been using it for a couple weeks and it works...
thingiverse
I made this support for tablets from the Dream Fitness treadmill, best sold here in Brazil. Pay attention to the supports, because if they are placed on the thread it is very difficult to remove later Fiz esse suporte para tablets da esteira...
thingiverse
This a simple tablet holder for the FYC JK8801F Folding Treadmill. ...The area for devices is far too small for a tablet to sit in landscape view, so I created this that slots into the existing device holder.
thingiverse
Their treadmill's book/tablet holder is too low. I needed something to be towards the top of control panel. Version 2 Screws are easier to print horizontally (stronger IMO than vertical print) and don't need much support. Two main stands are...
thingiverse
My Proform XP 542e treadmill latch broke and the company no longer makes the replacement part. I designed a replacement in Tinkercad and printed it. This will work with the 542e, but you have to already have the bolt and spring parts from the...
thingiverse
I created this for my wife's treadmill to hold her Galaxy Tab 10 tablet while she uses her treadmill. Nordictrack sells a molded plastic tablet holder for over $100. After a few hours of design and a night of printing I have a working tablet holder...
cgstudio
Pro Treadmill ProForm 2000 gym fitness and sport exercises training equipment.Modern high tech exercise machine for running in one place with digital control system.Modern high tech portable fitness training device for jogging, running or walking in...
cgstudio
Treadmill ProForm Pro 2000 home jogging and running sport exercise machine.Contemporary treadmill exercise machine for running, walking and athletic activity. Heavy-duty treadmill exercise machine for healthy lifestyle activity.For home sport...
thingiverse
Wanted a tablet at eye level for my 2020 Nordictrack 2950 treadmill (https://www.amazon.com/), so i made it in tinkercad. It snaps on to the small gap in the screen housing, and is sized just right for a Galaxy Tab S7. It also works on an ipad 10" -...
thingiverse
A tablet stand for treadmills. ...I designed it for my needs, but I believe it will fit most tablets and most treadmills.
thingiverse
Updated 3/19/19: Small changes to the hinge parts to make it stronger and easier to adjust. ... This stand will hold a tablet and clamps to top of a treadmill's control panel. It allows for better angle and height for viewing. ...
thingiverse
I wanted to use my old Nexus 10 on my treadmill, but the magnetic charger is on the bottom of the tablet. I made this panel to accommodate this. ... Say thanks by giving <a href="https://paypal.me/NialMurray"> OldGaf</a> a tip and help them...
thingiverse
... the device to hold the tablet even better. How I Designed This It was pretty easy I measured the treadmill and my tablet and whipped it up in Sketchup. ... First printing was a success, which is a good thing because my Solidoodle seems to be jammed.
thingiverse
This is a Tablet or Microsoft surface mount for the Reebok Treadmill. Print 2. ...
thingiverse
this tray is for the superfit treadmill if you print with plenty of infill it can support a 2 in 1 laptop be warned there are no guides on the sides to prevent sliding, but I find that things don't really slide, if for you they do I recommend adding...
cults3d
this tray is for the superfit treadmill if you print with plenty of infill it can support a 2 in 1 laptop be warned there are no guides on the sides to prevent sliding, but I find that things don't really slide, if for you they do I recommend adding...
thingiverse
I recently purchased a used Proform C42 treadmill model PCTL2932.0 which did not come with the safety key needed to run it, so I made this one. I also made a clip to attach to my clothing while using the treadmill, and connected it to the key via a...
thingiverse
This is a tablet stand for a NordicTrack T23.0 Treadmill. The design is a custom design which will only clip on to a NordicTrack T23.0 shaped display unit. When attached It will place the tablet close to eye height. The cool thing about the design is...
thingiverse
wanted a tablet at eye level for my 2950 treadmill, so i made one. This clips on to the small gap on the top of the display. Fits a Samsung S7 tab, but should also work with a 10-11" ipad. Hope it works for you! ...Note you have to print 2 of these for...
thingiverse
Print Settings Printer: MBot Grid II+ Rafts: Yes Supports: Yes Resolution: 0.3mm Infill: 20% Notes: Clamp was designed for my treadmill handlebars that are 25mm thick, but should work well for bike handlebars as well of similar size. Holder was made...