prusa filament guide 3d models
260158 3d models found related to prusa filament guide.thingiverse
Remix of Prusa Filament Guide by wawaChief. ... Adds a small nub which helps keep the guide attached to the frame.
thingiverse
Filament Guide for the Prusa i3. ... It helps to keep the filament unrolling smoothly.
thingiverse
This is a filament guide for the prusa i3 mk3, if you do not use the original filament holder and are using a standing behind filament box for example enjoy
thingiverse
Replacement for the Prusa i3 MK3 extruder filament guide. ...It has a M6 tap on top to screw a PC4-M6 pneumatic fitting or the dust filter available here : https://www.thingiverse.com/thing:3254151 Enjoy :)
thingiverse
Yet another filament guide for Prusa printer. It sets on the metallic frame under the filament spool as shown on the photo. Edit : In this new version (V2), the filament hole is slightly higher so that it won't hit the extruder on high Z positions.
pinshape
Summary Yet another filament guide for Prusa printer. It sets on the metallic frame under the filament spool as shown on the photo. Edit : In this new version (V2), the filament hole is slightly higher so that it won't hit the extruder on high Z...
thingiverse
This is a snap-in filament guide for a Prusa MK3s (unknown if it will fit other versions) I like to feed filament from a table-mounted spool holder rather than from the top so I designed this, using some parts from D3D_Designs filament guide:...
prusaprinters
I created multiple guides and wanted one center on the Prusa spool holder.
thingiverse
... the spool from turning. This can prevent print head movement, causing layer shifts. This part clips on to the standard Prusa spool holder and provides a guide for the filament so that it cannot get caught in the side of the spool during a print.
thingiverse
... is the MG Tall version. (Minimalist Guide Tall [+1/2 inch) I like these two the best. They do the job and print in well under an hour. I have standardized on the spool holder from Joseph Prusa at https://www.prusa3d.com/prusa-i3-printable-parts/
thingiverse
A filament guide to feed the extruder from above. ...Replaces one of the Z axis smooth bar retainers.
pinshape
A filament guide to feed the extruder from above. ...Replaces one of the Z axis smooth bar retainers.
thingiverse
This is derived from mpluma's "Filament spool holder for Prusa Mendel" http://www.thingiverse.com/thing:48856 . I needed a guide that would hang out to the side somewhat to work with my filamant spool, and really like the style of mpluma's spool...
prusaprinters
This filament guide is designed for printers with spool holders mounted behind the printer. ...I print with the left side down and cut the tab (only 1 layer thick) to allow for easy filament insertion.
prusaprinters
I made this guide mountable on the on-top filament holder, so it is mounted in the middle of the printer. ...Also, I added one small hole for the second filament - my on-top filament holder can have two filaments, where one is in the service, and...
thingiverse
We run the 10LBS/ 3K roller of filament this cannot go on top of the printer so I made this to help it work so well I thought I would share it. ... this is my first up load I hope I did it correctly
cults3d
Filament guide to put on the top rods of your mendel prusa.
thingiverse
Filament guide to put on the top rods of your mendel prusa.
prusaprinters
Check out the 2.0 https://www.prusaprinters.org/prints/72157-prusa-mk3-filament-guide-20Filament guide imbedded in the Z-Axis top part, the only thing you need is a piece of the PTFE tube.Print instructionsI recommend printing the part in 0.15mm...
prusaprinters
<p>No support needed. ...Printed with Petg and 20% infill.</p>
thingiverse
There are lots of great filament guides on here but i needed something to keep the filament closer to the frame as I am mounting an LED there so I designed this to fit to the new style Prusa twin spool holder. ...
prusaprinters
I like the symmetry of the dual appearance, and each filament getting its own loop......even if there is no practical reason to have two. It can be used as a single guide (as the original designer intended) by printing either the left or right side...
thingiverse
As shown here: http://things.hands.com/thing/PrusaFilamentSpool/ this ensures that the filament on a spool mounted on my variant of the prusia spindle comes off the spindle cleanly. ...The improvement compared with the version I based it on is that it...
thingiverse
Prusa Giraffe Filament Guide 02 This simple yet robust filament guide helps guide filament from the spool to the feeder without interfering with the printing rails at any stage. A single small zip-tie is used to affix it to the Prusa frame, and...
thingiverse
Guide for Filament on the Prusa i3 Printer : + Filament Guide. + Guide Extender. + Clamp suitable for 6mm acrylic. ... Cheers, Bantum ...