prusa i3 extruder mount 3d models

Screws with small heads might damage the holes becouse of the weight of the extruder. Do not tighten the srews for the bearings to heavy the bearings will get out of line and will not run smooth. The small blocks for the belt are fixed with M2.5 bolt...

This is a custom extruder mount made for my prusa i3 to allow for a tube feed extruder.

This is a modified version of Raj's Minimalistic extruder mount so it fits the i3 rail spacing

The old: I had trouble with the original extruder mount provided. It was printed so that stress from the spring was transversal to the layers. It warped under heat from the extruder motor and a layer or two began to separate. The spring tension was...

I have a wade extruder, a Prusa i3, and no way to connect the two.  So, naturally, I designed this mount so I could mount my extruder to the standard x-carriage. ... I hope you all find as much use for it as I did!

This is a fan mount for a 32mm fan (screw points) to fit a 3D Printer Czar Prusa i3. ... UPDATE - it works with M3 screws for attaching the fan Prusai3extruderfanmount2.stl

This is a simple Bulldog extruder mount for a Prusa i3 which is based on the mount that comes with the Bulldog kit, it can be used with either a Bulldog Lite or XL Extruder. Also included is a 25mm Fan Mount which mounts underneath the extruder to...

The screws is one M6x12 and one M3x14.

Extruder Mounted Fan for the Prusa i3 : Extruder Fan Mount : Replaces the extruder retainer clamp on of side of extruder ... Suitable for either type of Fan Mount ... Do Note : this is an earlier version, for an alternate fan mount - please go here...

This can be used to mount your bowden extruder to the Prusa-i3 frame. I haven't printed it out yet but i will try soon and post the results when i have. UPDATE: I have printed it out and it all fits nicely in eachother! ...The files include different...

I did not have bolt holes in my extruder so I designed one to be held by the 2 holes for the X assembly. ...Enjoy!

Re-works of a Extruder Mounted Radial Fan to suit the Prusa i3 : Fan Slide Bracket : Temporary fix for mounting the Cooling Shroud. ( Will be revised later ) Fan Extender arm : Connects between Extruder mount & fan Bracket ... Radial Fan Bracket...

Just added a support fot the X-axis switch to use it in my Anycubic Prusa i3. Also added holes to mount Bltouch/3DTouch sensor. The bad part is that you will loose some X and Z mm. UPDATE 20/02/21 New V2 version. Added holes for inserting...

... simple) and I wanted to use it with my prusa i3 rework printer. ...I modified the mount and clamp to fit the dimensions of the UBIS ceramic hot end The original source is from an extruder made for E3D hotend http://www.thingiverse.com/thing:257811

This is a printable direct drive extruder mount for Prusa i3 that contains auto bed level sensing using the extruder tip. It holds a NEMA 17 motor. Also: there is a mount plate for a dragchain. ...

Moved the nozzle down 8mm. ...Had some trouble on my printer after levelling the bed :-)

This is a remix of Geeetech Prusa I3 8mm Acrylic Top Extruder Mount which I edited to fit my laser cut 6mm prusa i3. Print Settings Printer: Prusa i3 Rafts: Doesn't Matter Supports: Yes Resolution: 0.3mm Infill: 5% Notes: I would use more infil to...

This is designed for use with an extruder that you can assemble from part available from Robot Digg. ...The fan shroud is designed for a 50mm fan, The 1H revision has an addition bracket for cable retention.

This is so that the extruder upgrade can be fitted to a CTC i3 (Prusa clone) in a direct drive format. The original bracket has holes which sit too close to the x-carriage for these cheap extruder upgrades to fit, so this deals with that problem. Not...

Just a quick remix which allows the use of two nuts & bolts compared to original, as I wanted to print the extruder mount on the Anycubic Photon in resin, which I imagine is too brittle to withstand the necessary bending to pop the stepper motor in.

If you use a PBC Linear Slide for the X-axis this is a small adapter plate to be able to mount a Prusa i3 vertical remix of the Greg's Wade extruder. Works with a J-head and e3d, might not work with a shorter cold end. ... Leaves you plenty of room to...

This is a bracket for mounting a MK8 extruder to the X-Carriage of the Prusa i3 Rework. I didn't like any of the available brackets so I designed my own. It seems to fit the extruder and X-Carriage well. But I haven't tested it on a working printer.

While building a prusa i3 mk2 variant for a friend I found myself needing to mount a direct drive extruder to the stock i3 x carriage. I started with Ghosty's part as I like how it moves the fan to better cool the heat break. I wanted to give the...

... that the gears end up skipping because the PLA gets soft. I made this mount for a 20mm fan (https://www.amazon.com/gp/product/B077GJCW7B/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1) to push air thorugh the opening to help cool the bondtech extruder.

Reinforced extruder mount using 4 lm8uu bearings

Print Settings Printer: HICTOP Prusa i3 Rafts: No Supports: No Resolution: .2 or .1 Infill: 10% for smaller parts, 20% for the main part. Notes: Supports are built...

... this is my version for the Geetech Prusa i3 acrylic. ... I am really happy with the results. Best printed in PETG to ensure that the carriage remains flat. Print Settings Printer: Geetech Prusa i3 Rafts: No Supports: Yes Resolution: 0.2mm Infill: 20%

Updates: 10.01.2016 New version in http://www.thingiverse.com/thing:1257733 Print Settings Printer Brand: RepRap Printer: sunhokey prusa i3 Rafts: No Supports: No Resolution: nozle 0.4mm layer 0.2mm Infill: 50% Post-Printing powered by 2x srew M2x47...

Remix from the following: Top Mount - Geeetech Prusa i3 Pro - Cable Chain Top Mount by Piggei Chain Ends - Geeetech Aluminium Y Axis Cable Chain by Bernbout Extruder End Mounts - Geeetech Prusa i3 - Cable Chain Mounts remix by Babokaj CURRENTLY...

Prusa i3 Rework Extruder side fan mounting Print Settings Printer: big printer Rafts: No Supports: No Resolution: 0.26 Infill: 60%