prusa i3 x carriage 3d models
397726 3d models found related to prusa i3 x carriage.thingiverse
Sunhokey prusa i3 x-carriage replacement 4 bearings LM8UU. ...Print Settings Printer: Sunhokey Prusa i3 Rafts: No Supports: No Resolution: 0.2mm Infill: 30% Notes: ABS
thingiverse
This x-carriage uses the same four hole mounting system that is used on the Prusa I3 rework 1.5 kit and most designs on thingiverse, so you'll need to print off a compatible x-carriage mount. My Bowden X-Carriage Mount for E3D V6:...
thingiverse
You need to change the belt This is the x carriage for sunhotkey prusa i3. The carriage allow you to use 4 linear bearings to improve the stability. The principle for this design is make it as light weight as possible, yet simple and that will allow...
thingiverse
Using M3-25mm to screw "X Carriage Cap" on x carriage. I use belt attachment part at following link. The file name is belt_x.stl. [belt attachment part for Anet A8](https://www.thingiverse.com/thing:1433295) I use LM8UU belt holder part at...
thingiverse
This is a fairly simple edit of [JackWaterfall's Prusa i3 X-carriage](https://www.thingiverse.com/thing:2514659/remixes) to better fit printers with centred belts. The original version had my belts rest at a weird angle, this edit keeps everything...
thingiverse
Prusa i3 Hephestos X carriage modified to use MK8 extruder (with the mounting plate). Created with FreeCAD. ...Print Settings Printer: Prusa i3 modified Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 20%
thingiverse
Carriage for the Design from MazaaFIN Smooth X-axis for Prusa i3 with Leadscrews (https://www.thingiverse.com/thing:1103976)
thingiverse
Prusa i3 X Carrriage assembled backward for Stepper motor position.
cults3d
X Carrigae for Prusa I3 modified for Jonaskhueling extruder and T2.5 belt
thingiverse
X Carrigae for Prusa I3 modified for Jonaskhueling extruder and T2.5 belt
thingiverse
Upgraded version of x-carriage for Sunhokey Prusa i3 2015-edition. It requires 2 extra pieces of SC8UU and is ment to be used with E3D-V6 hot-end full kit. It is made to maximize Z-axe travel. Included fanduct mounts to the main carriage...
thingiverse
This is a Micro Prusa X Carriage that only needs 2 LM8UU/Igus bearings, one for the top slot and one for the bottom slot. Keep in mind, this is a work in progress and is the first iteration. I have not tested it yet but it should work. Features:...
thingiverse
UPDATE: X-carriage 2 closes off the channel for shorter bridging without support UPDATE 2: X-carriage 2.1 closes off the channel for better bridging, also allows for press fit bearings and a better fit for the belt. ...The platform is slightly higher...
thingiverse
x carriage for less vibration in the x direction. ...I've been using it for a couple of months now and its worked really well
thingiverse
4 Bearings X Carriage Remix with deeper holes so you can use the Original m3*10 Screws. Various Improvments to reduce overhang. ... Changed hole of the thogh belt clip to fit a m3 screw
thingiverse
Also something to note is that the Nema17 I have is about 40mm deep so if you have something deeper you're going to need a bigger adapter, I'd probably go for a different design in that case - one that can lift the motor clear of the x-carriage...
thingiverse
You can mounth stpper motor differently. ...(Backward) Print Settings Printer Brand: Prusa Printer: Prusa Steel Rafts: No Supports: No Resolution: 0,2 Infill: 20 Post-Printing
thingiverse
Therefore, there is no wasted place taken by the strap attachment and the carriage has a wider sliding range. There are three bearing housing which is sufficient for the linear guide while keeping an isostatic assembly. It's recommended to insert the...
thingiverse
There should be an extra of 30mm since the carriage wont hit the frame anymore. The version with the orignial bearing blocks is less because of the rear bearing hitting the frame at the angeled edges. The other version is for bronze bushings, wich...
thingiverse
The GT2 belt was rubbing so I added a channel. The channel also secures the belt better. ... Chamfer on over hang removes need for support material.
thingiverse
Made a new design from combining http://www.thingiverse.com/thing:742947 and http://www.thingiverse.com/thing:438632 with an E3D v6 hotend adaption.
thingiverse
It was outlined with Openscad especially for You, to get You an ability to Customize It!
thingiverse
A single piece replacement for the laser-cut Prusa i3 style printer x-carriage. ...1 Piece instead of 3 pieces...
thingiverse
33mm square Laser module mounter for prusa i3 x carriage. ... stl data and 123d source.
thingiverse
Prusa I3 X-Carriage for Igus linear bearing ( 8x16x25 mm ) remix on blender
thingiverse
This thing triggers the X carriage endstop for the Replikeo Prusa i3 that is using http://www.thingiverse.com/thing:547706 as a bowden x-carriage mount. ...Print Settings Printer Brand: RepRap Printer: Prusa i3 Rafts: Doesn't Matter Supports: Doesn't...
thingiverse
### Description This is a x-carriage cable mount for the 3dprintingstore.co.za Prusa i3. Wanted a better way to keep the cables out of the way, designed this to bolt on to the current x-carriage and protect the cables from fraying. ### Update ...
cults3d
Clippable X-Carriage for Prusa i3 Hephestos. Significantly more rigid than the original. Include a detachable belt holder (easier for assembly/disassembly). Rhino files included if you feel in the mood for throwing more thought in this. Other format...