prusa layer shift 3d models

However by using the "Marblevator Tracks.f3d" model, the track design options are countless.As usual, I probably forgot a file or two or who knows what else, so if you have any questions, please do not hesitate to ask as I do make plenty of...

In fact I most often just grab these instead of my actual metal bench dogs unless I really need the sturdiness or precision that my metalPrinting InstructionsYou should be able to get away with 0.2mm layer height easily, the XY-resolution is more...

The triangular plug itself is slightly flattened at the tip, which gives enough support to build subsequent layers, and the angle is high to avoid any overhang issues. I also implemented a cutaway on the side panel of the shelf. Both the panel...

(.2mm works as well as indicated by the white PLA pics)Temp:  200°CBed:   67°CPrint Speed:  50mm/s, first layer at 20mm/sWalls: 5Infill:  50%Supports:  Tree Installation notes:The intent of this design was to allow...

 Easiest to accomplish this with paint on Smart fill mode.It's important to have a total of 12 top and bottom layers on the corner pieces to assure the area under the hinge peg is solid.  If it has infill, it becomes a significant weak...

The more detailed your print the better, but I printed it with 0.32 layer height (who's got time to wait that long ;) ). I printed it with about 1.8mm total perimeter thickness and 15% infill. If in doubt, print it sturdy, as we will press on it. I...

Drops feature an intricate chain that adds an extra layer of style. Jhumkas showcase elegant, intricately crafted details. Hoops & Huggies offer modern yet classic designs perfect for dressing up or down. Ear Cuffs & Hugs combine the latest fashion...

I did a layer change at the top so that I could print the "exhaust pipes" in silver. I found them here: https://www.thingiverse.com/thing:1962421 and modified them to work. (Chopped off what I didn't need, filled them in part way to make them...

The layer height should not exceed 0.3 mm for this trick to work based on the supplied .stl files.Cable guide in the "fan below / no GPIO cutout" top plate variant.====================================================================Depending on your...

First may print smaller than the threaded hole was designed to be, due to the Squishing of the first layer. So thread the bolt through from the other side to open it up. To install as normal* #Third Disclaimer I am printing this on my Ender3...

A semi-transparent filament might help here, if it is too thick. Mine is printed with 0.2mm layer thickness with white EXTRUDR filament and the light inside is nicely visible.  Electric CircuitATTENTION: ALL ELECTRICAL WIRING IS...

To get all tolerances perfect, you should print all parts at 0,1mm layer height. TK_ring (variants) CL_Lock CL_Attachment GrabLocker SC_variant (variants) In theory, none of the parts is in the path of light but I'd still play it safe and print...

6 - In order to get the flat ACME letters to glue properly to the rocket, I spread a thin layer of glue on the whole letter, placed it in position, and then used a heat tool or hair dryer (very low temp) to soften the letter enough that it could be...

Each chip has two bodies, the middle body should have its infill adjusted as needed and remove all top/bottom layers. Print Settings → Infill → Top/Bottom Fill Pattern. See the 3mf group files for an example</p><h3>Chips</h3><figure...

I printed all the parts on an Ender 2 at .2 layer height. parts needed: Arduino pro mini 5V 16M: battery springs: https://www.banggood.com/10-Pairs-Silver-Tone-Metal-Battery-Spring-Plate-Set-for-AA-AAA-Batteries-p-1046111.html slide switches:...

Just so you know, the clips start at z=3.125mm, which may seem an odd measure, but is exactly 1/8 of the basic unit and also allows for a bit of flexibility when it comes to adaptive layer heights and z-based color changes. You might also cut the...

Enabling the fan continuously with ABS is only feasible in the following cases: * for small objects printed with thin layers. Be sure to increase your print temperature if you do, and seal the enclosure to keep the air inside cozy and warm. A raft...

4.I have included some sacrificial layers to various holes in most parts to aid bridging when printing. These will require cleaning out prior to assembly. Operation Due to the flexing of the shaft there are a few quirks with this thing. I am still...

Tolerances are tight and depending on your printer settings (I used 0.2mm layer height on my Vyper) they might be too tight to slide them into place. As written they are designed to slide in from the side and can hold the rod with bearings just fine...

O-rings13 - 4-40 x 1/4" screws1 - 4-40 x 1" panhead screw1 - 4-40 nut1 - #4 washer1 - Standard poker-sized deck of cards (textured finish cards work best)All parts were printed in PLA with 0.2mm layer thickness, 3 perimeters and 20% infill. Use a...

The cable going down to the station needs to be clamped to the base to protect the reed wires.Printing configurationLayer height 0.2mm0.4mm nozzle15% infillWhite PETG filamentBlack TPE / TPU filamentplace gauge and base part upside downautomatic...

Print the 8 safe tiles in gray.&nbsp;Print instruction: PLA, 15% infill, 0.20mm layer height.&nbsp;Board x4. (you can do a color change when printing just like on the photos. I have included a 3mf file with the color change)</li><li>Blank_tile x6 for...

I printed with a layer height of 0.2mm, but I don't think that it too critical. Post-Printing **ASSEMBLING THE ROCKET** Assembly is pretty straight forward as you can see from the assembly diagrams. Hook the holes in the grip over the pins in the...

The LED light board gets inserted into a clip that clips onto the battery. The picture is a bit misleading as it is not as bright as the picture makes it look. I designed this with the idea of using clear PLA for the first 2 layers for the window...

I printed with a 1 mm nozzle at a layer of 0.3 and low speed (this requires material, in addition, my extruder cannot heat very much). It is important to prevent overheating, as the part may become deformed.<br/> You will need an Arduino Nano board,...

0.2 mm layer height is fine. After printing (v1.1 and earlier): remove the support parts (X or L shaped). Do not attempt to remove the square-shaped central shaft in v1.2 and later. Developed by Robotics and Mechatronics, University of Twente, in...

Just so you know, the clips start at z=3.125mm, which may seem an odd measure, but is exactly 1/8 of the basic unit and also allows for a bit of flexibility when it comes to adaptive layer heights and z-based color changes. You might also cut the...

I personally printed with PETG because I like the feel of it more than PLA, and printed with only 3 walls, 4 top/bottom layers, and 10% infill because weight matters more than print quality or strength. I also added some tape on top to give my...

I recommend 15-20% infill and a layer height of 0.1mm because most of the parts have round curvy bits, but 0.15mm or 0.2 will be fine as well.Here are the colors you should use if you want to match the model as closely as...

... Tough PLA only. No problems, very stable. The gunstock did survive one or two unintended drop tests. :-D All models, beside the Quest 3 controller mounts, can be printed w/o supports. I would recommend a brim for better adhesion of first layer.