prusa mk2s 3d models

Bottom parts connecting motors to the frame are actually a remix of Original Parts: https://www.prusa3d.com/prusa-i3-printable-parts/ Does not require any hardware or software changes. @ +0mm with reinforcement:...

I decided to build a clone of the Mk2S Prusa, utilizing leftover parts from my Mk2.5 Full Bear upgrade. I chose to incorporate the printed y-axis designed by pcky, which can be found at https://www.thingiverse.com/thing:2836470. After experimenting...

To fix that, I created a fortified base with much better results. The file "fm_single..." includes one complete Prusa RC3 face shield with the fortified base. The file "base..." includes only the fortified base of the face shield. Fits the...

Prusa MK2 and MK2S Upgraded Power Supply Unit Y-Axis Component Created by Evanrude is Distributed Under the Permissive Creative Commons - Attribution License Version 3.0. ...http://creativecommons.org/licenses/by/3.0/ Original Design Based on Josef...

This is my remix of https://www.thingiverse.com/ObjectReality s excellent remix of an Octopi Raspberry Pi case for mounting off the 10mm bar on the side under the heatbed of a Prusa i3 MK2 or MK2s. This is purely for use when combined with...

This is my remix of ObjectReality's excellent remix of an Octopi Raspberry Pi case for mounting off the 10mm bar on the side under the heatbed of a Prusa i3 MK2 or MK2s. This is purely for use when combined with...

I own a MK2S, and it might also work for other Prusa i3 models. I'm not sure if it will fit on other models, so let me know in the comments if you have one that uses the same PSU case. To use this design, remove the PSU and install a bracket in its...

After I remixed another adapter to make his case fit my new MK2S, I realized that I could easily adapt his original case to include my adapter as an all-in-one solution. Thus, I remixed my own adapter plate (https://www.thingiverse.com/thing:2334079)...

You can solve this by moving the mounting rods accordingly. Try it and leave some feedback :-) Happy Printing! Print instructionsCategory: 3D Printer Accessories Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: No...

However, a [NTC 3950 100K Thermistor](https://www.amazon.com/Happisland-Thermistor-Wiring-Printer-Heatbed/dp/B01N4KY6TR/) can be used as a drop-in replacement without any issues.* This design provides a complete extruder and hotend holder for...

Print instructionsCategory: 3D Printer Parts Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: No Resolution: .15 Optimal Infill: 100% Notes: All tested parts printed in ColorFabb NGen (as I have lots) I'd normally print this...

For details see here: https://www.thingiverse.com/thing:2663667 Print instructionsCategory: 3D Printer Accessories Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: No Resolution: 0.20 Infill: some 40% Notes: Note that I have...

I've used a logitech C615 webcam which has tilt, up/down adjustment so you can get the required angle. There are 4 slots on the bracket which can be used to feed a cable tie or two through to cable manage any excess wire on your camera. If you prefer...

Thus I remixed my own adapter plate (https://www.thingiverse.com/thing:2334079) and hofftari's case (https://www.thingiverse.com/thing:1325370) to come up with this new design. This also eliminated the M3 bolt that was originally located inside the...

Here's what's different than the original source: - Removed the "rest" support on the left (the one on my printer broke off) - Added a support to bolt onto the lower bolt of the small left fan - Added a divisor to make sure certain amount of air is...

Most of the printed parts are copies of STL, OpenSCAD and DXF releases from the original Prusa Git. The license is GNU GPL v3. All other parts (screws, nuts/bolts, shafts etc.) and electronics were built by me for this model, but all credit goes to...

To make it work, I remixed this model to widen the opening and accommodate my MK2S belt pulley. To secure the pulley in place, I used an extra bolt that came with my machine. While this works fine, a hex bolt would be easier to work with given the...

Merged two documents to enable a Logitech C310 camera connection on my Prusa i3 MK2 3D printer.

I built an enclosure for my MK2S using a modified Ikea Lack table. As I didn't want to remove the power supply and mount it under the table, it needs some fresh air inside the enclosure. To solve this issue, I drilled 1x 75mm hole A right next to...

This is a cover for the S-400-12 Power Supply for a Prusa I3 MK2. ...License GNU GPL v3 This is a modified Version of the openscad file von J.Prusa The mount holes on the frame need to be changed.

I aimed to offset my fan in this way so I could create space for viewing the print from the front of my MK2S printer. This setup saved me a significant amount of time, as all I had to do was add the gap. To be honest, I'm not entirely convinced by...

At the request of mrhappydude, I put together a PSU fan mount for the MK2S. This initial version isn't designed for a 120mm fan as he requested; instead, it's for an 80mm fan because I didn't have any 120mm fans on hand. Option 1: This mount should...

When I built my MK2S, I aimed to incorporate dampers from the start, but was let down to find that the y-axis stepper relied on just two screws for attachment. After running the i# for several weeks and growing weary of the constant y-axis noise, I...

I Designed This Modification for My Latest Build Because the Direct Extruder Wasn't Cutting It.\r\n\r\n\r\nThe Model Is a Modified Version of the Original Prusa STL File.

Cable guide for Prusa i3 Mk2 Extruder cables, prevents the issue of the 3mm filament guide coming loose from the Rambo case. ...Fits straight onto the current case guide using cable ties.

I've swapped out the Prusa heatbed cable cover to put those nuts at the bottom where they belong. ...Two different versions of the files are now available for your use.

... that is working flawlessly. Prints: 2 x Z-Motor Guided Top V3 STL files 2 x Z-Motor Holder 4mm V2 STL files 1 x Y-Belt Holder Longer 2mm STL file This setup enables the use of all Prusa I3 parts on the Reprap.me Acrylic frame from reprap.me.

Want to add cable chains to your MK2S without modifying or reprinting the Rambo Case or Extruder assembly? Then this just might be for you. Looking to replace zip ties with cable management? This could also work for you. (MK2 Support Read below) ...

This is an upgraded RAMBO circuit housing for the Prusa i3 mk2, a reworked version of the original model available on the Prusa website. After two months of use, a fan cable broke due to excessive stress caused by a tight fitting on top. I decided...

... to ensure proper alignment with the extruder-cover, as the new design rises higher than the original 8mm version. Printer Settings: Printer Brand: Prusa Printer Model: Prusa Mk2 Rafts: None Supports: None Resolution: 0.2-0.3 mm Infill Density: 25%