ps eye 3d models
42553 3d models found related to ps eye.
thingiverse
Hab eine PS Eye Halterung für unter ein Hängemöbel gemacht. ... Einfach mit einem Powersrip ankleben.
thingiverse
A 20cm remake of 3ChrisDs Simple PS Eye Stand. ...Well its a bit higher
thingiverse
# PS Eye LED Mod ## Description Modification on a PlayStation Eye camera to add LED. The modification is reversible. ## Parts - PS Eye camera - 5v LED Strip - Short wire 22AWG, 4cm ## Steps 1. Teardown the camera. 1. Solder the wire to CN1: Red =...
cults3d
Used to mount fpv camera lenses to the PS Eye. The thread is a bit tight but it should work, I don't know how to make custom threads in SW so I had to improvise. ... Also, the mounting holes will probably get occluded during printing, they should be...
thingiverse
... ...They are attached to the wall with either two nails or sticky tack and the PS Eye sits in the base. ...Make sure to read <a href="https://github.com/cboulay/PSMoveService/wiki">this</a> if you want to setup PSMoveService.
thingiverse
Used to mount fpv camera lenses to the PS Eye. The thread is a bit tight but it should work, I don't know how to make custom threads in SW so I had to improvise. ... Also, the mounting holes will probably get occluded during printing, they should...
thingiverse
A shoe for the ps eye camera. !!IMPORTANT!! I added a feature that the camera can only go in by one way. It should stop it from falling out. Just heat the threaded rod a bit and then drill the thread into the hole on the bottom. I suggest to...
thingiverse
PS_Eye_Syncmaster_2443_stand for opentrack. ... Included .step file.
thingiverse
Lens Filter holder designed for the PS Eye camera. ... For 5.8 cm radius lenses
thingiverse
The PS Eye fits like a glove and the whole assembly holds great to the bed, and requires no screws or anything special for the assembly. Files: - Regular, might need supports (depending on orientation - With custom supports, spaced 0.3 mm from...
thingiverse
A mount to hold the PS Eye Camera on the IKEA LACK table leg. M5 holes. The cover needs some sanding. ...Try printing at 98% size or lower to avoid.
thingiverse
A simple PS Eye mount for the Anet A8 and other printers with the same stepper motors. Mounts on either Z-axis motor for v1 and v2. v2.5 and up only mount on right side. Use original hardware*(a little close right now so i will add holes for the...
thingiverse
This is a simple stand for the playstation eye camera to put it next to your printer. ...It is 13cm tall.
thingiverse
I had an older Playstation Eye(PS3) that was gathering dust. While they are not the best cameras (640x480) it was free. This mount should work for anyone with 2020 rails. The base is designed for t-slot nuts and M4 or M5 bolts. You may use...
thingiverse
An angled arm for PS eye Mount (https://www.thingiverse.com/thing:4094009) Suitable for mounting your PS eye camera onto vetical frames, such as Kossel Liner Plus. ...
thingiverse
simple and strong support for PS eye camera for screen, to be used with a computer with CL Eye drivers https://codelaboratories.com/products/eye/driver/
thingiverse
This is a remix of 1ProjectAWeek's PS Eye Cam Mount. ... I modified it to mount on the bottom part of the Monoprice Mini Delta.
thingiverse
Made a mount for the PS eye. Extended the arm because the cam is larger than a gopro. ...Thickened the arm because there was too much room under the bed to decrease wobble.
thingiverse
... Eye Camera Mount for the Qidi Tech X-One. ...The camera mounts to where the handles would normally be. There's a friction fit to the camera, but I also used some hot glue to hold it in place. PS Eye Camera https://www.amazon.com/gp/product/B0072I2240
thingiverse
My PS Eye mount for Ender 3 v2. There is no need for screws. It slides right to the main 4040 profile of the base and the camera goes on the top of the mount. ...The camera base should slide right into the top of the mount and happily sit there.
thingiverse
PS Eye support mount for Anet A8. I was inspired from this project: https://www.thingiverse.com/thing:3207437 But I did't find anything really good for my 3d printer. ... I use it with a Raspberry Pi 3 B+ with Octoprint
cults3d
My PS Eye mount for Ender 3 v2. There is no need for screws. It slides right to the main 4040 profile of the base and the camera goes on the top of the mount. ...The camera base should slide right into the top of the mount and happily sit there.
thingiverse
This is a mount for the PS Eye to clip tightly onto the side of the Anycubic Kossel's Power Supply. It hooks into the 120v/240v switch and jams itself into the PSU lower housing. ...Both the bracket and camera fit very tightly.
thingiverse
PlayStation 3 EYE as webcam for AstroPrint. ... Print in Cron PLA 1.75mm RED Extruder 205'C Bed 60'C No extra support needed.
thingiverse
Support to stabilize the Arm, if your Arm is very long and shaky.
thingiverse
This is my first remix if the model you downloaded is REALLY big for some reason, the downscale is 10%. To achieve the same results in the photos, you are going to need probably a: - Glue or hot glue (sorry, the hole is slightly bigger, getting...