ps2 controller case 3d models

rc car flight controller

ps4 cookie cutter controller

Nintendo Gamecube WaveBird Controller

controller cookie cutter

Xbox One Front Controller

DC3200 TEMP CONTROLLER

Kelly Motor Controller

VaporizR controller cover

Kicker Bass Controller

Controller Stand Elden Ring

Quest3 Controller Stand

Phone to controler holder

Xbox_Controller_Stand

This holder lays in the dust filter cut out of many standard computer cases. It has a hole for rubber fan mounts, which are not necessary but can be used. It fits most standard LED controllers. This holder measures 90mm tall, 45mm wide and 9mm...

PS4 controller case for the first duashock 4. I measured the whole inner life of the dualshock 4 and modeled my design in fusion 360. I print it a few times and adjust the model. The case is hard to print on the FDM printer. I think the results ...

This is a custom controller stand designed specifically for Gaems' Playstation 4 Carrying Case. It seamlessly slips over the ledge, expertly holding your controllers securely in place when not in use. Furthermore, it enables effortless charging while...

This is the casing for the 18650 Solar Charge Controller. Originally designed for use with the Solar Tracker, which includes a rig and controller, it has been adapted to work with Cycling Helmet Solar Panels. The package contains face-plate/labels...

Part of the kit was this low voltage board that was bare, so I designed this case to enclose it. kit was <a...

This attachment ensures the controller stays securely fastened to your hands - unless you shake them too vigorously, in which case it might detach and fly off into your TV screen during an intense Dance Central session. **Note:** The Quest...

Here are two brackets for the CNC 3018 Off-line controller (see attached photo to verify the correct controller version) you have two versions with different fixings, respectively you will have the controller support which will be fixed on the sides...

This is a component part of a 3D Printer enclosure projectIt contains one Raspberry Pi 4 which runs Octoprint with PSU Control, Enclosure Plugins.Rpi GPIO are connected to a breakout board with some electronic component to power (12v, 5v, GND) and...

RelativeCCSender::setMode(MACKIE_CONTROL_RELATIVE); ---------------------------------- After the sketch has been uploaded to your arduino and everything is working, you can assign the different controls to whatever parameters inside Bias FX 2. ...Make...

The switch is supplemented by a lever switch panel that makes turning the switch off SO easy.The dimmer speed control is varied by a case mounted potentiometer. Attached to the potentiometer is a custom 3D printed rotary knob. The knob provides...

An accessory is available that enables the controller to be housed in a separate case, keeping it distinct from the CNC. This also helps safeguard the cards from any potential chip debris. ...The design files for this part can be found within Solidworks...

Printable case to built a Vectex Controller Plug. ... Needs a 9 Pin D-SUB female connector (Conrad part number 1401502 - 62 | Digi-Key part number 732-618009221923-ND) and a anti-kink sleeve for 4mm cables (Mounting hole is 6mm x 4.5mm, 2.8mm wall...

Case for LogicDesk 'additional' controller: https://github.com/klym-tatarnikov/RoboDesk Standing desk height can be adjusted in normal way (up/down buttons) and additionally 2 fixed positions can be reached by double clicking on 'up' or 'down'...

I constructed a case for the Arduino controller created by Mechatronics on YouTube. If you're interested in building one, check out this video link: DIY Arduino RC Transmitter. ... https://howtomechatronics.com/projects/diy-arduino-rc-transmitter/...

This is a case for the Dreamcast Controller Converter, or "Adapter for MAPLE Bus" from https://www.dreamcast-talk.com/forum/viewtopic.php?f=5&t=13058 There are 2 versions, the newer one supports a display. Have fun. ... TinkerCAD Link: ...

... of the new Re-ARM controller. ...So we can start making cases for it The .isg was supplied by the manufacturer, I converted it to .stl No idea on the licensing on the .igs, if it need changing, let me know. Print instructionsCategory: 3D Printer Parts

- Relocated rear buttons to front (be aware these are smaller buttons than the top ones) - Relocated controller board standoffs to rear - Relocated the cable hole to the top of the case (the cover now holds in place vs the rear button).