ps2 controller holder 3d models

Custom Clamp: Mount Ikea Dioder LED Controller Securely on Ikea Desk Leg Use Integrated Channel to Hold Cable Tie in Place Print Settings: Rafts: Not Necessary Supports: None Needed Infill: 20% Fills Entire Part for Strength and Durability Production...

Custom bedside stand holds Sunbeam heated mattress pad controller. Designed for dual-zone version (https://amzn.to/38j4Lfd), it also fits twin zone model. ...Stand includes non-skid gasket installed at its base, requiring 3D printed flex filament of...

Remote holster designed specifically for the Hampton-Bay UC7078T wireless remote control. Print Settings: Printer: 3DWOX DP200 Rafts: Ignore - it doesn't matter. Supports: Yes, the printer has support capabilities. Resolution: High definition with...

A small print that allows to hang an playstation controller under or on the side of a desk. It only requires 2 additional screws or some glue to install it. ... To avoid use of supports, orient the object such that the back of it touches the plate of...

Wanted a keyhole mounted version for a few controllers... Make sure to print with supports! Changes: Added bridge in the middle of the base section for extra support Extended height to accommodate for keyhole hooks without wasting extra...

Every time I had to leave my controller I had to unplug the headphone jack. I decided to cut the space that was left over to solve my problem. ...If the same thing happens to someone, here I leave my remix.

This means anyone with a disability or impairment can use the controller in a non-intended way - without the strain of holding the controller or keeping it in place without slipping.The main feature of this design is the interchangeable controller...

I really liked this one: https://www.thingiverse.com/thing:3746195/ but i wanted to display the controller instead of lying it down. Also my headphone has a much smaller headband, so i reduced its size, and added a Steam Logo to make it nicer. I...

I made this to hold onto the LED ring part of the Windows MR controller. This makes it so I can hang the two controllers on my desk. Should work for other places you might want to put it as well as long as the width is less than 16.5mm. ...I'm sure you...

... negative wire in the Charge Box unit, adding extra wire if necessary. Securely fasten the LED volt meter box to the main charge controller box using 4 screws. ...Activating the switch will display the current battery voltage on the LED Volt meter.

Super simple model that I made by hacking together two other models from Thingiverse namely this PS5 controller stand and this Skadis hook. ...Aside from bodging the two together in Tinkercad I flattened the sides so that the model can print flat on...

The Recon Tower is a fully customizable headphone and controller stand designed specifically for your desk or gaming system. Each component prints seamlessly without the need for support structures. I'd greatly appreciate any feedback you can provide...

Upgraded the top bracket of the xbox one wall mount (credit to Wupinstick) to hold the xbox controller, designed specially for this bracket. Printed 4x walls, 6x top and botton, 10% gyroid infill and it's a bit overkill. 2-3 walls should have been...

It holds an Elite controller on one side and a gaming headset on the other. I have not finished the print so I haven't tested it yet. But I will post photos and updates once it's done. ... I'm new to the game so please share your comments, likes,...

By utilizing this upgraded component, pilots can easily integrate their flight controller or APM with anti-vibration mounts for reduced shock and vibration. ...When employing an APM, users can take advantage of 3mm standoffs to securely fasten it...

This version of mvoosten's remix of Athens3Ddesign's Xbox One Controller Stand has been specifically tailored for a PC dongle, boasting a slightly wider design and incorporating 45° chamfers within the hole to eliminate the need for supports - simply...

I was looking for a straightforward way to hang my controllers that didn't involve using the hole in the ring at the top since I've already filled it with magnets for a stock mount. None of the designs I came across met my requirements, so I took the...

it is originally designed for a switch of a Konnect controller. but if you want I can adapt it to your switch, just give me the dimensions and I modify the bracket. the support is held by two rislan. the switch is 22mm long, 13mm wide and 9.5mm...

Human, engineered to dock Moto G Phones onto the NES30 Bluetooth Game Controller for limitless Android gaming thrills with old-school NES/SNES titles and beyond. Built from two sleek models: MotoGClip-2 excels in simplicity, offering an unobtrusive...

It holds an Elite controller on one side and a gaming headset on the other. I have not finished the print so I haven't tested it yet. But I will post photos and updates once it's done. ... I'm new to the game so please share your comments, likes,...

... fan bracket. ...Use 4 self-tapping screws to attach the holder. It is possible to use two cheap 12V fans connected in series and connect them directly to the motherboard at the 24V output. ...Use 8 M3x14mm screws to attach the fans to the bracket.

**Add something grippy** to the bottom lip of the holder to keep the phone in place. I used a masking tape loop. Might not need **supports**, but I used them. It clips on snug: **very satisfying**. (https://youtu.be/9MN3rmHZccQ) The slvs...

... please leave feedback. ...Aprox 3.5 hour print time. Gaps 8mm wide for common remotes. Indents on bottom are for rubber feet. Included in your model is a 1cmx1cm cube to check for scaling, if the cube needs scaling to match, do the same to the holder.

---------------------------It is very uncomfortable to go with the controller in one hand and the drone in the other so I designed this adapter for controller strap. It is fastened with velcro so you do not have to break anything, it can also be...

... It utilizes only the hardware that comes with the printer for mounting the screen, eliminating the need for any additional components. Still finding your controls too far away? ...Consider upgrading to a longer cable to bring them within reach.

This is a support to mount the David Clark DC One-X or Pro-X controller on a surface in an aircraft. I used a good two sided tape to fixe mine to the sides of my RV6. The part is not symetric... one side in the bottom is notched to accomodate...

This will securely hold the tablet and controller in place. I'm open to any suggestions for improvement. Here is the source file with all its parts: https://drive.google.com/file/d/1_42qckOReMPOLN-qIlOVDWprn9VjdHqM/view?usp=sharing You can also see a...

This creepy demon hand is highly detailed and it will look great while holding your controllers. It prints super easy and quick as it does not need any supports, and it has the size of a real hand. All of my models are for personal use only, unless...

I made these charging stands for my dad for holding his ps4 controllersPrint SettingsPrinter Brand:CrealityPrinter: Ender 3Rafts:NoSupports: NoResolution:.28Infill: 25Filament:Maths Pla Gold, RedCategory: Video Games

This is the Universal Controller Mount created by the3dcoder (https://www.thingiverse.com/the3dcoder/designs) with some minor modifications. Basically I removed a little volume from the part that fixes the piece to the wall to save a little material...