ps2 mount 3d models
348664 3d models found related to ps2 mount.thingiverse
EyeToy PS2 camera mount for Artillery Genius. ...Remix of https://www.thingiverse.com/thing:4257585 and https://www.thingiverse.com/thing:2363086
cults3d
With these two pieces we managed to anchor our Playstation 2 fat to the wall without any problems.
thingiverse
These are mounting plates for the PS2 fat model. It work with the Gamestar adapter and the original Sony hdd/network adapter. Just snap these onto the sides of the drive and slide it into the slot. It will be held securely. This is a revised...
thingiverse
Minimal wall mount i made up for the ps2 slim only the bottom clip should need supports side note i was thinking of adding a bolt hole to the bottom clip to mount it directly to the ps2
thingiverse
A mount for an "old" PS2 Eye Toy camera. ... This replacement plate is designed to mount the camera on the wall/ ceiling.
thingiverse
Insert bottom first, than rotate. ...(will not work if top of controller is inserted first) https://www.tinkercad.com/things/fL5nwrufhiF-ps2-controller-wall-mount
thingiverse
This is a wall mount designed to be used with the console flat to the wall. Made to require minimal usage of filament. I used screws for wood. Having 24.5 mm of length, a screw thread diameter of 3.5mm, and a head diameter of 8.5mm The wall...
thingiverse
This adapter suits the PlayStation 2 Expansion Bay with ethernet that has the sliding/moving metal brackets for IDE/Molex. This allows easy and secure installation of the widely available SATA adapter kit available for this. The screws in the...
thingiverse
This is a simple wall mount for the PS2 EyeToy camera, which I'm using with my OctoPi. The two screw holes are 3mm in diameter. ... Print it upside-down and you won't need any supports.
thingiverse
For mounting you have to remove the backplate of the camera (the screws are under the sticker with informations) and also the small screw in the backplate. Please pay attention to the washer! Then you use the small screw and the washer from the last...
thingiverse
Just secure the drive to the mount, plug the drive into the HDD/Network adapter and carefully place it inside the console. There are probably better ways to do this but this was a quick and dirty model I made to satisfy my own needs. ...Hope it helps...
thingiverse
This is a wall mount designed to be used with the brick flat to the wall. Made to require minimal usage of filament. I used screws for wood. Having 24.5 mm of length, a screw thread diameter of 3.5mm, and a head diameter of 8.5mm The wall must...
thingiverse
Two separate mounts for the Playstation 2 Eye Toy camera for use with the "Articulating Raspberry Pi Camera Mount for Prusa MK3 and MK2", to allow bottom or top mounting for better monitoring. The bottom "webcam stand" mount is based on the "EyeToy...
thingiverse
This is a design for a lap stand for the Pelican Cobra TT Racing Wheel (Model PL-624) for the PS2. The company did manufacture its own lap stands, but if you bought one of these second-hand like I did you likely do not have one! The "Right" and...
thingiverse
Camera mount is for PS2 Eye Toy camera. This positions the camera view directly inline with the print nozzle. Camera mount can be secured to X-carriage mount with 3mm screw and nut or 3mm insert. Sliced WITH CURA 4.8 - using tree supports. ...
thingiverse
Design I designed a converter for a 2.5" HDD to fit in my PS2 (with the network adapter, and the SATA mod) without it floating around. The bracket slides into place, where it holds firmly. Hardware All you'll need are some small screws to mount...
prusaprinters
DesignI designed a converter for a 2.5" HDD to fit in my PS2 (with the network adapter, and the SATA mod) without it floating around.The bracket slides into place, where it holds firmly.HardwareAll you'll need are some small screws to mount the HDD...
myminifactory
A small mounting system that I use to mount my games on my walls. ...I use strong adhesive double-sided tape for attachment.
cults3d
very easy to print design, works perfectly for pla, pla+, abs. ...ps2 wall mount.
cults3d
PS2 Logo as a decoration. ...You can adjust the size in your slicer and make it as big as you want.
thingiverse
Having my old PS2 stack on top of some other electronic devices would close the airvents of the device under the PS2. In order for this device to be able to breathe and sort out its cooling, I created these risers for the PS2. Though designed for the...