ps2 slim case mod 3d models

I was really impressed by how easily the official pi 4 case snapped together with a satisfying snap, but I was let down that there wasn't an easy way to add a fan to cool the hot pi. I adapted another design by minorcoma that allowed you to drill...

Add four spacers and voila, a "free" RPi case. Simply install three plus four spacers glued beneath the RJ45 and composite out. There's just enough room for everything else. If necessary, drilling in at the bottom with an M3 drill bit will work fine....

... are then filled with parts that must be rewired with new LEDs before gluing. The wires can directly connect to the pre-existing switch and power supply for lighting up the figure inside the case, rather than just the outer edges of plexiglas.

An update now adds a cover for Allted's Gnarly Rambo Archim Case with five keystone jacks. His Gnarly_Sexy_RA.stl file must be located in the same folder as the OpenSCAD file for modification. ... The keystone jack was borrowed from mwu at:...

I designed an inner frame for the Pi Grrl2 to hold all electronics together as a single unit, which then attaches to the front of the case while the back serves only as a cover, greatly simplifying assembly. Updated cases reflect changes made to...

http://www.thingiverse.com/apps/customizer/run?thing_id=813330 Instructions Using the following options: 6_perimeter_tolerance = .5 6Plus_height_tolerance = .2 5height = 7.6 6Plussthick = 1.5 pattern_thickness = 5 4width = 58.55 4_height_tolerance =...

If you line them up correctly and glue them down you won't have to cut the case - I just didn't line them up well and using the Dremel was easier than reprinting or dealing with the superglue. The USB hole is larger in the stl than it was on the...

Remixed from the Ender 3 Electronics case found on Thingiverse here: https://www.thingiverse.com/thing:4071141 The parts contained here are just what I modified for my needs. I used the unmodified parts from the original model for other things like...

Remix of "Wemos 18650 charge circuit shield case" incorporating adjustments.First, my slicer/printer refused to deal properly with the screw holes on the bottom so those are changed to use flat head screws.My PCB's USB A ports were attached out of...

This panel works directly with luc_e's "Raspberry Pi 7 Inch Touchscreen display case"Feet slide into the dovetail on the back, leg extenders make it more stable and simply fit into the hole in the bottom of the feet.If you glue a small electronics...

... the trick to remove the oxidation layer for solder to wick. - Use thin wires for the voltage indicator board as to fit inside the casing - inject a bit of hot glue where the power lead and balance plug exits to keep it in place from being tugged on.

From the Rotor Riot video instructional on how to convert Panasonic NCR18650 3400mah batteries into Fatshark lipos with battery level indicator, I designed a custom case to complement it. The design is extremely tight-fitting and I strongly advise...

... layer for solder to wick. Use thin wires for the voltage indicator board as to fit inside the casing inject a bit of hot glue where the power lead and balance plug exits to keep it in place from being tugged on. ... Category: R/C Vehicles

A fried of mine got handed an FHP12A mini optical power meter with a broken case and he wanted to 3d print a case for it and have it with a litium battery. No sure how the step down pwm frequency effects the accuracy. ... Battery: 603040 or smaller...

... it to fit as expected. This part was not modeled in Solidworks, but instead cobbled together in TinkerCAD. It is rough, but it works. I have included the stl for just the chain connection part as well, just in case you need it for some reason.

Case for Unisolder 5.2 http://dangerousprototypes.com/forum/viewtopic.php?t=7218 https://github.com/5N44P/unisolder-notes Iron Connector Used: LUMBERG KFV 81 Changes: Added front iron connector Easier to print no support needed anymore Added some...

Dimensions, screw hole placements, and knob movement restrictions are taken directly from the popular PS2 analog joystick module for Arduino, available at...

mod

Mod

For those of you who do a bit of console modding and are wanting a bracket to hold an SSD in a PS2 storage bay. I found some other brackets were a bit flimsy and left a bit of room for the SSD to shake around so i made a bracket that occupies the...

Modified the great H2 modular case by myang777 to fit the new H3. Adjusted cutouts on the top plate to suit the slightly larger heatsink and repositioned headers. Unfortunately, there is now very little space between the heatsink and the...

PS2 Vertical Stand compatible with HDMI Adapter (with USB Cable on the Bottom)

PS2 2.5mm Harddrive caddy Holds the harddrive in place with no movement, even without screws

Hai there, This Fold Spen attachment for Z Fold 3 with Spigen Slim Armor case. ...Made it removebale but you can add double side ducktape for glue to make it permanently attach.

Customers are eagerly awaiting the release of the PS2 Fat console and are ready to print out two units as soon as possible.

This one is for J-version with TTL -external triggering (FW -110 or newer) and PC connectors. The kit's mother/display board connectors are recycled for those extra connectors so unit is like 1/2 cm slimmer than standard one (see the picture). ...

This is a personalized adaptation of the Thing found at http://www.thingiverse.com/thing:58001. ...It was crafted using the Customizer tool available at http://www.thingiverse.com/apps/customizer/run?thing_id=58001, which allows for unique...

Users can access modified 3D printing files which feature augmented wall density and reshaped designs at www.thingiverse.com/thing:29021

<p>I have made a remix of the <a href="https://www.thingiverse.com/thing:711669">http://www.thingiverse.com/thing:711669</a>.<br/> I invert the position of the heads screw and made it to use some DIN7982 M2,2x13 Countersunk Head Tapping Screws.<br/>...