ps3 controller phone holder 3d models
436421 3d models found related to ps3 controller phone holder.thingiverse
I needed a holder for the PS3 controllers I bought for the grandkids. I wanted something light and small. Decided to design one. ...This prints best on its side with supports and raft.
thingiverse
Easy to print holder for two PS3 controllers. Put it all together with contact glue. Notes: 1. You may need to sand a little bit to fit the holders into the base. 2. Take care to have the wide part of the base plate to the rear. 3. Note...
thingiverse
PS3 / 4 controller holder i got half of this model off thingiverse, can't tag original designer as i can't remember who it is. I modified the holders to add a long base. The item is split left / right as its too big for my 300mm print bed. will...
thingiverse
created a wallmount for a PS3 Controller that easily snap in and fitting tight. i mounted it on a board. Btw: print it with the wallside laying on the heatbed to get a better strength at mount. PS: if you´re donwloaded this one, please...
thingiverse
For use with chickenbisket's 360 holder base. ... Might work with the DS4, but I don't have one to test.
thingiverse
This is a Controller holder for the PS3 in the front,left and right is PS3, on the top MW2 and MW3, on the stopper COD and on the back the 4 main Characters of the story (Captain Price,Ghost;Jury and Soap) on cura you can't see the text but on the...
thingiverse
The Playstation 3 Move Navigation Controller is a wand-style bluetooth game controller that is essentially half of a standard PS3 SIXAXIS. As it is bluetooth, it can be used for purposes beyond gaming (such as remote control of arduino robots). I...
thingiverse
Just a quick and dirty remix of breckenedge's PS3 Controller Stand (https://www.thingiverse.com/thing:867761) to fit a PS3 controller onto my skadis boards. ... It still needs some work to get a bit more stable and better looking, maybe with integraded...
thingiverse
I got tired of my controller getting knocked off my desk when I wasnt using it so I decided to create a mount for the side of my monitor which is an old dell, however I think the angle and size of the holder should fit a range of monitors. Its my...
thingiverse
Sony Playstation controller holder. ... 1 single piece model, thin and easy to print.
thingiverse
Couldn't find a base I needed, so I modified Webberen's to suit my needs, and here it is if it works for someone else. It is made to be screwed from under a shelf or desk. I drilled to holes for screws. Works great, thanks Webberen. ...Print Settings...
thingiverse
Ein PS3 Ständer um unter der PS3 etwas luft zu bekommen . ... Print Settings Printer: PrusaI3B Rafts: No ...
thingiverse
Flexible xbox controller phone holder. Works best on newer model Xbox S controller with usb c port. Hold nearly any sized phone. ... Print with PLA and no infill.
thingiverse
I made this holder because i wanted to have at the same print both my phone and my xbox controller
thingiverse
A Ps3 controller holder. Don't fit as good than my Ps4 version but is ok. ...Print Settings Printer Brand: RepRap Printer: ...
thingiverse
Based on PS3 Controller Under Desk / Table Hook by charlesjcarr, this hook allows keep the ps3 control under the shelf without connecting the USB cable to stay safe
thingiverse
I wanted an under the shelf PS3 controller holder, but found ShaoPellini's design had slight gaps on my PS3 controllers that left a slight wobble. The hole allows for the charging cable, and I've found if I stick the charging cable through both...
thingiverse
This is a remix/mix of two Xbox controller phone holders that I liked a lot. I liked both designs, so I decided to customized them a bit to create my own phone holder. I recommend priting at 60 mm/s (if using an Ender 3) and to use as an infill...
myminifactory
... can be easily attached to any standard PS3 controller. These designs allow users who are handicapped or disabled to use a standard PS3 controller with very little effort or modifaction. ...This method is also very cheap and quick to put into place!
thingiverse
A simple Rack for your PS3 Controller with two holes for 4mm Countersunk Screws add 1-3 % in Cura for a better result
youmagine
To connect an phone, cut the controller cable off and splice on a usb cable (leave the yellow wire disconnected), and then use a microusb otg adapter to connect to the phone. tested in cyanogenmod 10 and 11 on a samsung galaxy s relay and a samsung...