ps3 eye ir filter cap and guide by 3d models

I scalled down the original model from Wrongdiagram to 98% anb it's now a "snap" fit when printed in 0.2mm layer. ... I also designed a round guide you can use to cut the filter(s) the rigght size.

cap to place over the ps3 eye lens, uses a piece of a rubber band to lock properly in place. ... photo film is used as IR filter material.

Small support for an IR filter to go on a PS3 Eye for TrackIR.

I needed an adapter to mount my 34 mm infrared filter in front of my PS3 Eye camera in order to use it for Freetrack. ... All radius parameters in customizer are meant "holder inner" - so you just input your actual measurement of your camera/filter...

This is infrared filter holder made from old floppy disk for PS3eye camera. This is supposted to be used with opentrack software. ... Maybe you will need to set the scale of model, for me works 98%.

I designed a canvas to cut a daylight filter to the right size for the ps3 eye. Simply cut the square, then the corner. ... It also come with a small "shim" that will hold the filter in place inside the webcam (drop the filter on the lens, then drop...

I used this to test the use of exposed, developed film as an IR pass filter. (it also doubles as a cylindrical surface to attach a mount to if you have damaged the existing stand.. AHEM). The inner part should be printed in black, so as to reduce...

A simple lens cap for the PS3 Eye. ...Protect the lens while hiding your shame ;) Print Settings Printer Brand: RepRap Printer: ...

Lasercuttable PS3 Eye camera (chip only) + filter case. Inspired by:http://nuigroup.com/forums/viewthread/9473/ Instructions Lasercut this from 4mm material. ...This size works best for the wire hole and the filter holder.

Ps3 Eye cam Cap and supports.

This was originally designed to install a filter using a floppy disk on my PS3 Eye for a DIY trackir. I used it for a while with good results, but finally decided to open the camera to remove the IR filter anyway, so I finally installed the filter...

This was originally designed to install a filter using a floppy disk on my PS3 Eye for a DIY trackir. I used it for a while with good results, but finally decided to open the camera to remove the IR filter anyway, so I finally installed the filter...

This was originally designed to install a filter using a floppy disk on my PS3 Eye for a DIY trackir. I used it for a while with good results, but finally decided to open the camera to remove the IR filter anyway, so I finally installed the filter...

PS3 eye camera mont

Ps3 Eye Camera inside PCB

Originally made by TrackHat, this flexible clip allows for attaching a ps3 eye camera to a monitor. ...Enjoy.

I also remixed a front mounted cam shelf bracket (https://www.thingiverse.com/thing:1774153) that was designed for the Wanhao i3 / Monoprice Maker Select and made it shorter so that I could screw the modified lid onto it. I then screwed the base...

Unfortunately the support that ships with the camera only allows the camera to stand up vertically which is not very handy for multi-touch tabletops and other applications where you want the PS3 Eye to point upwards. Thanks to the Makerbot, you can...

... On Amazon they sell for 13$, so save ya moniiiiii!!!!!!!! Ps3 eye: https://www.amazon.com/PlayStation-Eye-3/dp/B000VTQ3LU/ref=sr_1_1?dchild=1&keywords=ps3+eye&qid=1590112539&sr=8-1 - you need cl eye test to use with computer. ... -stay safe

This is a sleek wallmount for the ps3 eye for your VR tracking needs. the wallmount part has a hole to screw it to the wall, then the arm slides just into the wallmount. ...if the cameramount part has not enough friction and moves to left and right...

This is a pan and tilt assembly for the PS3 Eye Toy. You need to unbolt its original foot, then bolt it into the holder (the screw head is inside the camera itself). The tilt servo housing is based on a mg 955. The pan holes are set at 1.5cm...

Simple mount to mount your PS3 Eye camera to your Ultimaker. ...Handy for webcam view when your using Octoprint for example.

Cover for lens on the PS3 Eye Camera Shown in image is my GoPro Mount for the camera found here: https://www.thingiverse.com/thing:4107345

This model is designed to replace the back half of the ps3 eye camera shell in order to add a more easily mountable base to the camera. The lower with arm and two provided bases are designed to be held together with a number 8 bolt, and then mount...

This is a guide and filter mainly for Alfawise EX8. ... It was designed as remix for https://www.thingiverse.com/thing:3033662 but I created brand new model with using knowledge from https://www.thingiverse.com/thing:6455 Maybe the holes are too...

Edit it online https://www.tinkercad.com/things/dRm6k8T3rZY i recommend using the file titled "ps3 eye mount fixed" and printing it on the large wall for minimal stringing and print with supports everywhere i sliced it with cura and printed it on the...

The new version should fix this issue and allow the camera to sit flat Mount for the PS3 Eye Cam that allows you to use GoPro Mounts. The clamp mechanism was inspiration from ChristianCooper's mount system:...

I've built this model for using my PS3 Eye as webcam on my PC. Feel free to use this model as you like (you may sell if you want it). If you want to contact me, you may call me in my instagram (https://www.instagram.com/shannondcabral/). ...

Simple mount for ps eye

This macro lens is from a low-cost set from amazon. ...It came with a fish-eye and wide angle I believe. 19x5.5 The focal length seems to be about 15-25mm. Tpu worked for me. ... Better than nothing.