ps4 vr camera stand 3d models
307788 3d models found related to ps4 vr camera stand.thingiverse
It`s a replacement support for VR PS4 camera. You must print 2 and clamp them to the camera. ...The holes are suitable for insert three M3 thread rods with nuts and join both parts.
pinshape
The only post process needed is to round the camera screw hole with a 13/64" bit and then make the threads with a 1/4"-20 bit. I also had to file down a bit of the plastic at the back for the camera wire to slide in correctly. ...This is due to...
thingiverse
The only post process needed is to round the camera screw hole with a 13/64" bit and then make the threads with a 1/4"-20 bit. I also had to file down a bit of the plastic at the back for the camera wire to slide in correctly. This is due to...
thingiverse
Inspiration of PS4 (Fat) Vertical stand" by Marcus24. I've created a dock for the VR-Processor. ...
thingiverse
This thing is made for the Playstation 4 VR Camera to put it onto a tripod.
thingiverse
... camera. ...Loops at the back are to secure cord with small ziptie. Works best for getting a downward angle. You may need to scale up by 2540% to change from mm setting. Remixed from PS4 Camera Clip here: https://www.thingiverse.com/thing:1884607
thingiverse
This is retractable mount for the newer version of the PS4 camera for PSVR. The camera hides behind the TV when not in use to keep your room clean and minimal and lifts up and locks when in use. I added a flat part on the outer slot so you can...
thingiverse
I bought a used PSVR but it didn't come with the camera stand, so I decided to design and print one! It fits the camera nice and snug, so you can rotate the camera in it and it'll hold its rotation. ...I put some of these rubber feet on it to keep it...
prusaprinters
I bought a used PSVR but it didn't come with the camera stand, so I decided to design and print one! It fits the camera nice and snug, so you can rotate the camera in it and it'll hold its rotation. ...I put some of these rubber feet on it to keep it...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/44MP3RLG4rA inspire from http://www.thingiverse.com/thing:377368 i made it to fit my SHARP 70" Print Settings Printer Brand: RepRap ...
thingiverse
Holder for the processor unit of the Playstation VR. ...With LED hole (this should be on the right place:) and cooling holes.
thingiverse
Ps4 stand 4 the ps4 camera on ps4. The stand is fixed. ...It works 4 me, maybe it will 4 U
myminifactory
This is ps4 camera holder on a ps4. ...You can move holder over camera lense to block for privacy
thingiverse
This is a slim stand for the original PS4 (fat), it helps to keep the PS4 cool as it allows ventilation when the PS4 is in a vertical position. ...This slim stand raises the console 1.5 cm and is smaller than the original stand but keeps the console...
thingiverse
Vertical stand for the original PS4, two stands need to be printed for one PS4. Air channel in the base to allow better air flow to the vents on the side of the PS4. ...I printed at 0.15mm layer height in PLA but it could be printed at 0.10mm or 0.20mm...
thingiverse
Just an "original PS4" vertical stand with logo. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/01vXbxuMNYB
thingiverse
This is simple PS4 stand. I have used on mine and I am content with result. ... Printed with resolution 0,4mm but I recommend 0,2mm
thingiverse
With this simple stand you can place your PS4 on a upright position and it becomes enough air to cool down quiet. Its very simple to print, with one side the PS stand very high and with the other side it stands not so high. I hope my english is not...
thingiverse
This is a table like peace of art that was made by combining the bottoms of rectangle to the tops of circles to get the organic looking effect. ... if you want to make it look like the ps4 stands in the image make sure it is scaled to 5 cm tall.
thingiverse
Vertical stand for Playstation 4. Original design created on Fusion 360. ...Works great!
prusaprinters
This is a simple stand for a Play Station 4. ...Just print two in .30 layers.</p>
thingiverse
It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter embossing doesn't need it. Spade - Infil to add weight, no supports Letters - Print flat, already scaled to...
thingiverse
Here we have a box where the PS4 3D Headset Cable box can be attached to e.g. ...trousers...
thingiverse
I model it because i want it and didnt find it For VR 143x143x37mm