psu bracket 3d models

PSU Bracket A quick 'n dirty u bracket for mounting a PSU to, say, a wooden board. The dimensions of the PSU are: - height 50mm - width 110mm The length of the bracket is actually 110.3 to allow for some margin. This is not needed for the height. ...In...

PSU Bracket A quick 'n dirty u bracket for mounting a PSU to, say, a wooden board. The dimensions of the PSU are: - height 50mm - width 110mm The length of the bracket is actually 110.3 to allow for some margin. This is not needed for the height. In...

Very basic PSU Bracket for the MK3S Black PSU. With my lack stack against the wall I ran into trouble with the suggested mounting of the PSU, either the switch and power connector were unreachable or the air vents of the PSU were facing the wall. ...

I needed bracket to hold my PSU under the desk

This is a bracket for 150W PSU. PSU dimentions: 198x55x38. Once I moved to 220V Silicone heater for bed I don't need 360W 12V PSU with active cooling, that generates additional noise. So, I moved to 150W PSU without fan, passive cooling and...

this bracket attaches the psu around the threaded rod under the heated bed. you may have to increase the size by 1000%. the lines in the holes are meant to be supports to keep the bridging neat. ...they can be easily broken through afterwards

i needed a way to hold my PSU for the Ultimaker 2 clone i am gona build, så i made this one, i will post pictures of it mounted soon screws used 4 x M3 10mm 4 x M4 8mm Print Settings Printer: Prusa i3 Rafts: Doesn't Matter Supports: No Resolution:...

This bracket attaches a 12V 30A or 5V 30A power supply on its side. A notch is included to secure the power supply to the bracket. ...Print Settings Printer: Maker Select I3 ...

Simple bracket to attach the switchable power supply to one of the columns. 2 prints are needed. ...Print Settings Printer: FLSUN Delta Kossel ...

Psu rear bracket. ...For ender3 pro whit double z-axis&nbsp;</p>

**Latest Version Posted Here: http://www.thingiverse.com/thing:3763705** This is a custom PSU bracket designed to raise the Dan A4 V4 PSU mounting points up about 5mm. This provides additional room for the cabling with use with a 92mm AIO (such as...

# Motivation Although there exists the thoughtfully designed [official ATX PSU bracket](https://coolermaster.egnyte.com/fl/d18M4dx90F#folder-link/), I had trouble using the official design with my EVGA G3 850W (which is 150 mm in length): * Front...

I evaluated different PSU mounting brackets and found http://www.thingiverse.com/thing:1636876 to be a simple and elegant solution. The thing is: it does not fit my PSU. I decided to create a customizable version so everybody can now make a pair for...

Just an other Prusa MK3 PSU-Bracket / Brace. My Frame has a Skew-Value of 0.01 ! (Support Menue)</p> <p>Please have a look on my other Prusa MK3 Prints <a...

Customized version of https://www.thingiverse.com/thing:1949437 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1949437

This is a replacement SFX PSU bracket for the Ncase M1. ...It uses a total of 5 countersunk screws to make it secure. Three of these screws are already used for the original SFX PSU bracket, but there are extras for use behind the case's front panel.

Broke the SFX PSU Bracket that came with the case so I made this one, looks much better anyways. ...Leaves just enough room for a 25mm thick fan on top.

PSU mount for 2020 extrusion Also a version without the end clip-ons. ...M3 screws to mount PSU to bracket. ...M4 screws to mount bracket onto 2020 extrusion.

AP201 SFX-L PSU Bracket Mounting the PSU this way allows a front 120mm intake fan, optimal airflow to the PSU, 360mm radiator with tubes on right side, and extends the GPU support to ~360mm. ... Filament used: HATCHBOX PETG Black...

these are some brackets, when I upgraded my Tarantula Pro with a bigger PSU it didn't fit the original bracket, and i couldn't mount it, with these brackets 2x PSU_bracket 1x PSU_bracket2 I could mount the PSU under the printer and these fit...

PSU bracket for Geeetech Rostock G2 G2S Requires 4 pcs M3 X 18mm ( or 20) Allen head + 4 pcs M3 nuts and mounts on the vertical 10mm dia rails ( 60mm center to center) Under the bed was too cramped and I wanted the PSU in plain sight. Designed to...

PSU bracket for Geeetech Rostock G2 G2S Requires 4 pcs M3 X 18mm ( or 20) Allen head + 4 pcs M3 nuts and mounts on the vertical 10mm dia rails ( 60mm center to center) Under the bed was too cramped and I wanted the PSU in plain sight. Designed to...

UPDATE (13 Nov 2017) : I added V2 of PSU Bracket OpenSCAD that allows for the clip length to be easily altered via new 'ExtraClipLength' variable. See the discussion in the comments tab. ...Print Settings Printer: FlashForge...

PSU brackets. Waiting for a replacement PSU so might have to adjust the height. This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/lIBZ7gFy21I

PSU chassis adapter bracket for Honeywell C200 Process Controller.

A bracket so I can mount the PSU under my desk at work and reduce clutter.

This is a bracket that I made for a standard 12V 30A PSU. ...Attached is an image of the exact PSU brand that was used as a reference for this model but it should work with similar models as well.

I designed this bracket to allow me to mount a 150mm x 86mm ATX PSU under a (Ikea Lack) table. It should work for a number of different configurations of ATX PSU, with mine having a 120mm fan on the bottom of the PSU. Printed with supports in its...

Another PSU mount, made of 2 brackets (left and right). Designed to be mounted on a case with M4 CHC screws. I had to put an ATX PSU tu replace my chinese crap... Design of Left bracket to be confirmed for the cable output ;-) Update: adjust the...

... Supply with an m4 Bolt. ... Optionally, you can bolt to your frame with m5 bolts. Not necessary as you can see in the installed photo - the PSU is clamped tight against the frame even without bolting to the extrusions. Use two brackets per PSU.